Bosch GWS 18V-15 C Professional Manual Original página 28

28 | English
Additional safety information
Wear safety goggles.
The protective guard must not be used for
cutting. With a suitable adapter, the protective
guard can also be used for cutting.
Hold the power tool firmly with both hands
and make sure you have a stable footing. The
power tool can be more securely guided with
both hands.
For application tools with an internal thread, such as
u
brushes and diamond annular cutters, attention must
be paid to the max. thread length of the grinding
spindle. The spindle end must not touch the base of the
application tool.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Release the On/Off switch and set it to the Off posi-
u
tion when the power supply is interrupted, e.g. when
the battery pack is removed. This prevents uncontrolled
restarting.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Store the application tools inside buildings, in a dry,
u
frost-free room at a uniform temperature.
Remove the application tools before transporting the
u
power tool. This will allow you to avoid damage.
Bonded cutting and grinding discs have an expiration
u
date, after which the discs must no longer be used.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery in the manufacturer's products or
u
those of the AMPShare partners. This is the only way in
which you can protect the battery against dangerous
overload.
1 609 92A 6WP | (08.06.2022)
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Caution! When using the power tool with Bluetooth
u
fault may occur in other devices and systems, aero-
planes and medical devices (e.g. pacemakers, hearing
aids). Also, damage to people and animals in the im-
mediate vicinity cannot be completely excluded. Do
not use the power tool with Bluetooth
medical devices, petrol stations, chemical plants,
areas with a potentially explosive atmosphere or in
blasting areas. Do not use the power tool with
Bluetooth ® in aircraft. Avoid using the product near
your body for extended periods.
The Bluetooth® word mark and logos are registered trade-
marks owned by Bluetooth SIG, Inc. and any use of such
marks by Robert Bosch Power Tools GmbH is under li-
cense.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for cutting and brushing metal,
stone, plastic and composite materials, roughing metal,
plastic and composite materials as well as making holes in
stone materials using diamond annular cutters, without the
use of water. Make sure that the correct protective guard is
used (see "Operation", page 37).
Sufficient dust extraction must be provided when cutting
stone.
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.
The power tool must not be used to grind stone materials
with diamond grinding heads.
With the Bluetooth Low Energy Module GCY 42 inserted,
®
power tool data and settings can be transferred between the
power tool and a mobile device by means of Bluetooth
less technology.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Unlocking lever for protective guard
(2) Direction of rotation arrow on housing
(3) Spindle lock button
(4) User interface (GWS 18V-15 SC, GWS 18V-15 PSC)
® , a
® in the vicinity of
wire-
®
Bosch Power Tools