Descargar Imprimir esta página

AVE domina smart 442TC14-W Manual Del Usuario página 2

Publicidad

Configurazione
Per le operazioni di messa in funzione del sistema seguire la configurazione guidata presente
nell'App AVE Cloud. Successivamente all'abbinamento del dispositivo al proprio impianto, la
configurazione avanzata dei parametri e delle modalità di utilizzo avviene mediante l'accesso alla
sezione EasyConfig presente nel menù impostazione dell'applicazione AVE Cloud (password di
accesso: "2").
Compatibilità Assistenti Vocali: Google Assistant® e Amazon Alexa®
In fase di configurazione viene richiesta l'abilitazione della modalità Access-Point Wi-Fi® in un
dispositivo wireless a scelta tra quelli presenti nell'impianto, al fine di consentire all'applicazione
AVE Cloud di connettersi ad esso. Se vi sono altri dispositivi DOMINA smart wireless IoT presenti
nell'impianto, è fondamentale che il dispositivo in questa modalità non sia quello più vicino al
ROUTER DOMESTICO, in quanto quello più vicino dovrà essere il dispositivo con abilitata la modalità
Root-Node (vedi immagine).
Procedura di reset
Per effettuare il reset e riportare il dispositivo alle condizioni di fabbrica, nei primi 60 minuti da
quando il dispositivo viene alimentato, premere per almeno 15s il tasto laterale PRG.
442TC14-W
ENG
The 442TC14-W multi-touch control block is a 2.4GHz wireless electronic device. It is a multi-function
appliance with IoT technology on standard Wi-Fi®to create IoT and IEEE 802.11 domina smart mesh
network systems. 230 VAC power supply, to be completed with 2-module touch plates.
The electronic multi-touch control from the DOMINA smart wireless IoT range has: two local IoT relays
(L1; L2) that act in pairs to control a diverter or roller shutter control (the two relays have an AVEbus
address). One contact closure relay (L3 - relay with no addresses) which close when there is pressure
on the keypad and open when the appropriate configured keys are released. An input (P) for an external
pulse command to switch relays L1; L2 if they are configured as diverters.
The front area of the device is divided into 9 sensitive zones, divided into 3 columns of 3 zones each.
The central zone, or the two high+low zones, or no zone can be activated for each column. You can,
therefore, have from a minimum of one (at least one zone must be defined) active sensitive zone up
to a maximum of 4 zones.
During programming, you can choose which zones to activate and which functions to assign by
configuring the columns:
• a column is used to operate the pair of local relays and can be configured by means of the
middle touch button to manage the diverter, or by means of the up/down touch buttons to
manage the roller shutter;
• the other two columns can be used to control:
- the local relay without address only by means of the middle touch button;
- remote devices through the sending of radio frames to diverters or IoT sockets with column
set by means of themiddle touch button, or up/down button, or both keys with different
controls; or scene retrieval.
There is also a mode in which none of the columns are connected to the local IoT load with an address,
in which case the touch keypad becomes a pure control element.
The device does not require a communication gateway and can, therefore, be managed in two ways:
• Wi-Fi® DIRECT mode. A device of your choice within the system is identified as a Wi-Fi®
Access-Point. By independently generating the Wi-Fi® grid, it enables local dialogue with the
AVE Cloud application;
• DOMESTIC ROUTER mode. A device of your choice in the system is identified as the Root-Node.
Connecting to the Wi-Fi® grid (generated by the home router) allows the monitoring, both local
and remote, via the AVE Cloud application and popular cloud-connected Voice Assistants.
IMPORTANT: the electronic device must be powered with the same Line (L) and Neutral (N) that powers
the load (see diagram). If the IoT diverter function is set, the load must be greater than 5W for correct
detection. If an inductive load is connected, we recommend installing an RC filter (snubber) to be
connected near the load.
Technical specifications
Mechanical
Compatible with all elements of System 44.
• Container:
• Degree of protection:
• Weight:
Signalling
Optical signals (LEDs) are visible on the front in the enabled areas: both the intensity and the colour
can be set during programming (blue, amber or purple). When the touch is recognized, the LED
emits a more intense light.
Button
Front touch buttons. Side button for programming (the button must be pressed using a slotted
screwdriver)
Connections
8-pole 16A 250V~ terminal block
• Insulation stripping:
• Screw:
• Tightening torque:
• Capacity:
• Opening:
• Terminal L1:
• Terminal L2:
• Terminal L3:
• Terminals P:
• Terminal L:
• Terminal N:
- IoT - 2-module Multi-touch control S.44
2-module S44 (45 l x 45 h x 40 d) mm
IP20. When installed in the appropriate containers: IP40
60 g
6 mm
slotted screwdriver head 3 x 1 mm
0.5 Nm
flex wire 0.14 ÷ 2.5 mm2 (26 ÷ 13 AWG)
rigid wire 0.14 ÷ 4 mm2 (26 ÷ 11 AWG)
2.5 mm x 3 mm
Line to IoT Device interrupted (Roller shutter Div/UP)
Line to IoT Device interrupted (Roller shutter Div/Down)
Line to First Local Stand Alone Button interrupted
Button input for remote operation
Line
Neutral
Scelta del dispositivo Access-Point Wifi
Scelta del dispositivo Access-Point Wifi
Root-Node è in posizione sfavorevole).
NOTA: L'impianto DOMINA smart wireless IoT permette la creazione
di impianti composti da massimo 50 periferiche Wi-Fi mesh.
Radio specifications
• Wi-Fi 802.11b/g/n
• Access point (AP) Station (STA), B, G, N or mixed mode -mesh network-
• WPA2.PSK encryption
Power supply voltage
• Rated voltage:
• Tolerance:
• Max absorption @ 230V~:
Weather conditions
• Reference temperature and relative humidity: 25°C RH 65%
• Operating ambient temperature range: from -5°C to +35°C (indoors)
• Maximum Relative Humidity: 90% at 35°C
• Max altitude: 2000 m a.s.l.
Controllable loads
If programmed as diverter
• Incandescent lamps: 500W @ 240VAC
• LED lamps: 100W @ 240VAC
• Fluorescent lamps: 120W @ 240VAC
If programmed as a roller shutter switch
• Engine load: 2 A @ 240VAC cosφ 0.65.
• Engine load: 2 A @ 100VAC cosφ 0.65
Protections
Overload and short-circuit protection
Insert a 1.5kA (min) C10 circuit breaker in series with the circuit
Overtemperature safety protection
PTC resettable thermal fuse built into the appliance. It trips when there are internal faults that may
lead to dangerous over-temperatures.
Regulatory compliance
• Radio Equipment Directive (RED). RoHS Directive.
• Low Voltage Directive (LVD). Standards EN61010-1, EN_61010-2-030.
• EMC Directive. Standards EN 61000-6-1, EN 6100-6-3.
AVE SpA declares that the radio equipment complies with Directive 2014/53/EU. The full text of the EU
Declaration of Conformity can be found in the product data sheet at the following address: www.ave.it.
Operation
By default the device is configured as follows:
• Central column for the actuation of the pair of local relays as diverter (middle touch button and
actuator equipped with AVEbus address);
• The other two columns are disabled;
Procedura di reset
Per effettuare il reset e riportare il dispositivo alle condizioni di fabbrica, nei primi 60 minuti da quando il
dispositivo viene alimentato, premere per almeno 15s il tasto laterale PRG.
After configuration, it is also possible to:
• Set the scenes and associate them with the front buttons available;
• Operate the L1 L2 relay pair with the function of an IoT light diverter or a classic ON/OFF switch.
The command executed remotely or by pressing the local button is interpreted as a change of
status;
• Operate the L1 L2 relay pair with staircase light function. The command executed remotely or
by pressing the local button causes the relay to move to ON for the set time.
• Operate the L1 L2 relay pair with standard roller shutter switch function. When the UP button is
pressed, the roller shutter moves upward (opening) for the time corresponding to the time the
button itself is pressed (<2s). When the button is pressed for a longer time (>2s) and released,
the roller shutter moves upward (opening) for the time set in the programming phase using
parameter 4 (Rise time). The same function is repeated for the DOWN button associated with
the closing of the roller shutter.
• Operate the L1 L2 relay pair with standard blackout roller shutter switch function. When the
UP button is pressed, the roller shutter moves upward (opening) with pulsed movements, the
number of which is set in parameter 12 (Number of steps), whereas the duration is set in
parameter 9 (Blade pitch time) and parameter 10 (Blade pause time). When the button is
pressed for a longer time (greater than the number of steps) and released, the roller shutter
moves upward (opening) without stopping for the time set in the programming phase using
parameter 4 (Rise time). The same function is repeated for the DOWN button associated with
the closing of the roller shutter.
• Operate the local relay without L3 address using only the middle button of one of the columns.
corretta.
®
non corretta (il dispositivo
®
230V~ 50Hz
±10%
1.2W, 2.6W with energized relay.

Publicidad

loading

Este manual también es adecuado para:

442tc16-w