VERTO 50G273 Manual De Instrucciones página 12

Charging station
9.
Charger
10.
LED
11.
Locking ring
12.
Spindle
13.
*Differences may appear between the product and drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY / SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
1. Battery
2. Charger
3. Charging station
PREPARATION FOR OPERATION
REMOVING AND INSERTING THE BATTERY
• Set the direction selector switch (4) in middle position.
• Push battery lock buttons (5) and slide out the battery (6)
(fig. A).
• Insert charged battery (6) into the handle holder, you should
hear when the battery lock buttons (5) snap.
BATTERY CHARGING
Drill is supplied with partially charged battery. The battery
should be charged in ambient temperature between 4°C
and 40°C. New battery, or one that has not been used for a
long time, will reach full efficiency after approximately 3 to 5
charge/discharge cycles.
• Remove the battery (6) from the drill (fig. A).
• Connect the charger (10) to a mains socket (230 V AC).
• Connect the charging station (9) to the charger (10).
• Put the battery (6) into the charging station (9) (fig. B).
• Once the charger (10) has been connected to mains green
LED will light up (11), signalling presence of charging
voltage.
• When the battery (6) is placed in charging station (9) red
LED lights up (11), which indicates that the battery charging
is in progress (fig. B).
• Green LED (11) turns on again when the battery is fully
charged (after 5 hours) or battery temperature is too high
(above 45°C).
When the battery reaches too high temperature
during charging (above 45°C) charging is interrupted.
Charging resumes
battery cools down. This temperature rise inside
the battery is not likely and may never occur.
Each time the battery is removed and inserted into
charging station during recharge, the charging cycle
resets regardless of the current battery level.
Batteries heat up strongly when charging. Do not operate
just after charging – wait for the battery to cool down to
room temperature. It will prevent battery damage.
- 2 pcs
- 1 pce
- 1 pce
automatically when
SPINDLE BRAKE
Drill is equipped with electronic brake that stops the spindle
immediately after the switch button (7) is released. The brake
ensures precision when screwing or drilling and prevents free
spindle rotation after switching off.
OPERATION / SETTINGS
Switching on – press the switch button (7).
Switching off – release the switch button (7).
Each time the switch button (7) is pressed, the LED diode (8)
lights up to illuminate the workplace.
ROTATIONAL SPEED CONTROL
Increase or reduce pressure on the switch button (7) to adjust
drilling or driving speed while operating. Speed adjustment
allows for a soft start, which prevents dill slipping when
drilling holes in gypsum or glaze, and allows for operation
control when driving screws in and out.
OVERLOAD CLUTCH
Set the torque adjustment ring (2) in appropriate position
to permanently set overload clutch to defined torque value.
When the set torque is reached, overload clutch disconnects
automatically. It prevents from driving screws too deep or
damaging the drill.
TORQUE ADJUSTMENT
• Different screws and materials require different torque to be
applied.
• The bigger the number corresponding to given position, the
bigger is the torque (fig. C).
• Set the torque adjustment ring (2) to appropriate torque
value.
• Always start operation with low torque.
• Increase the torque gradually until obtaining desired results.
• Use higher settings to undo screws.
• When drilling, choose setting marked with the drill symbol.
The torque is the greatest with this setting.
• Knowledge how to choose appropriate torque setting
comes with practice.
Setting the torque adjustment ring in the drilling position
deactivates the overload clutch.
INSTALLATION OF WORKING TOOL IN THE DRILL CHUCK
• Set the direction selector switch (4) in the middle position.
• Turn the ring of the quick release chuck (1) counter
clockwise (see mark on the ring) to spread jaws enough to
insert drill or driver bit (fig. D).
• To fix the working tool, turn the ring of the quick release
chuck (1) clockwise and tighten.
Deinstallation of the tool is similar to installation, only the
sequence of actions is reversed.
the
Make sure the tool position is correct when installing drill
or driver bit in the quick release chuck. Use additional
magnetic adapter as an extension when using short driver
bits.
DRILL CHUCK INSTALLATION AND REMOVAL
• Pull the locking ring (12) forward and slide the drill chuck (1)
off the spindle (fig. E).
• Installation of the drill chuck (1) is similar to removal, only
the sequence of actions is reversed.
12
OPERATION / SETTINGS