Luna ANH29 Manual De Instrucciones página 12

Remember!
•
Do not wear loose long hair, loose clothing or jewellery, which could become caught
up in moving parts of the tool and cause injuries and clothing damages.
•
A switched-on tool may be directed towards the work material only. Loose parts may
disunite and cause damages. A person or an object may become in contact with the
tool, which could cause an accident or material loses.
•
Cold or wet hands, smoking and snivel may increase vibration caused hazards.
•
Let the tool operate and by holding the handle use the least possible force. If possible,
the tool should be supported on a stable support block.
•
Interruption of work should be ensured or another kind of work, not involving use
of vibrating tools should be alternatively performed, in order to reduce the harmful
influence caused by the vibration.
•
Ensure that the workplace is well lit
Important information
Tools must be lubricated
Before use always lubricate the tool with a few drops of oil AIRTOIL 22 (Luna 15531-
0105) intended for use with pneumatic tools, by dropping it into the air inlet opening
of the tool. In case of continuous work, a pneumatic lubrication system (Luna 20571-
0106) should be used, adjusted to about two drops per minute. If the tool is not used
for a longer period of time, it is required to drop a few drops of oil before storage of
the tool, in order to reduce the corrosion risk.
Attention! Use only oil that is supposed for pneumatic tools. Use of other oils may
result in "clumping" of oil and reduction of the movement ability of the machine. It
may cause reduced work efficiency.
Leakages must be avoided
Avoid leakages in the air circulation system. Always use a thread sealing tape at the
point where the plug is connected to the tool. Pay attention that hoses and hose clamps
are in good conditions.
The compressed air must be dry
As cleaner and dryer the compressed air is, the longer is life time of the tool. In order
to ensure it, we recommend use of air filter, which removes water from the compres-
sed air, accordingly reducing eventual damages of the tool and connections caused by
corrosion. Remember to remove eventual water condensate from the compressor tank
and the compressed air supply system before each working day.
24
Instructions
•
Under no circumstances defective needles (Pos. 1) or needle equipment (Pos. 2)
can be used as it may cause injuries and material loses.
•
The plastic plug should be taken out of the air inlet opening (Pos. 4) and an
insertable hose connection with 1/4" external thread should be used, for example,
a hose connection.
•
Before start-up of the tool always make sure that the chisel or the needle-shaped
file is correctly fitted and properly tightened, otherwise the tool will not operate
faultlessly and will not provide the required work efficiency.
•
Replacement of the needles (Pos. 1) and needle equipment (Pos. 2): The tool must
be disconnected from the compressed air supply. Un tighten the screws (part.no
22) and pull off the front tube (part.no 21) plus unscrew intermediate tube
(part. no 20). Take away the spring compression (part.no 19), the anvil (part.no 16)
and remove the needles from the needle holder (part.no 17). Replace the needles
and assemble in reverse order. Tighten all screws securely.
•
Check air pressure and, if necessary, adjust it so that the tool would operate at
the required pressure and blow number per minute. Adjustment of the pressure
is performed by use of the compressor or separately installed pressure regulator
and adjustment of the blow number is performed by use of a separately fitted air
supply regulator (not included in the standard supply). Specification of the tool
complies with a 6 bar pressure.
•
Always be careful when using the needle hammer. A negligent attitude towards the
tool may cause damages of the internal parts and housing fractures. It may result in
reduction of the tool efficiency and the tool may loose its value.
Maintenance: Lubrication is essential as it ensures a low noise and vibration level. In
case of continuous use of the machine it should be cleaned and checked at least twice
a year.
25