Publicidad
Idiomas disponibles
Idiomas disponibles
EN
can be harmful to health.
Always remove the power cord plug from the mains socket before performing repairs. Unexpected start-up of the machine
during repair can lead to serious injury.
Do not use brushes with diff erent parameters than those specifi ed by the manufacturer. Incorrect insertion tool can cause
serious injury.
PRODUCT OPERATION
Preparing for operation
Caution! Disconnect the machine from the power supply before performing any assembly and adjustment work. Make sure that
the power cord plug is unplugged from the mains socket.
Visually inspect the product. If any damage is discovered, do not commence work before removing it.
Unpack the product and remove all elements of the packaging. It is recommended to keep the packaging for future storage and
transport.
Installation of the implement
Using the screws (II), fi x the brush cover to the housing from the side equipped with the tool holder.
On the other side of the housing, fi x the wheel using the screw (III).
Mount the additional handle at the top of the housing near the main handle. Gently open the ends of the additional handle and
slide it onto the mounting socket (IV). The tabs in the handle should fi t into the openings in the machine housing. The additional
handle angle can be adjusted in a stepwise manner by turning it at the place of installation. Secure the additional handle with a
screw lever (V).
Brush installation and removal
Warning! Due to the risk of injury, install the brush wearing protective gloves.
The tool holder is equipped with a latch allowing you to attach the brush without the use of additional tools.
The tool holder ring is equipped with wings. Grasp the wings and move the ring towards the wheel (VI). While holding the ring in
this position, insert the brush pin into the tool holder (VII). After releasing the pressure on the ring, it should automatically return to
the initial position and the brush pin should snap into the tool holder. Check that the brush pin does not slip out of the tool holder.
If it slips out, installation must be repeated.
Removing the brush involves moving the ring, holding it in that position, and then removing the brush pin from the tool holder. After
releasing the ring, it should automatically return to the initial position.
Caution! Remove any debris created during operation from the inside the cover and the tool holder each time before installing
the brush.
Adjusting the housing length and angle
The possibility of setting the housing length and angle allows for better adjustment of the brush to the operator and the workplace.
To adjust the length, turn the lower part of the housing ring in the direction indicated by the arrow, marked with the open padlock
symbol (VIII). The housing is telescopic. Once the selected length has been set, turn the lower part of the housing ring as far as
it will go in the direction indicated by the arrow, marked with the closed padlock symbol. Check that the housing does not change
length inadvertently during operation.
The length of the housing should be selected so that the machine is tilted during operation and the operator can freely hold the
brush by the main and additional handle.
To change the angle, pull the top of the ring up and hold it in this position (IX). You can change the angle of the lower part of the
housing relative to the handles. After setting the selected angle, release the upper part of the adjustment ring. If the upper part
of the ring automatically returns to the initial position and comes into contact with the lower part along the entire circumference,
it means that the housing has been locked in the selected position. Check that the housing does not change angle inadvertently
during operation.
Preparing the workplace
Before commencing work, prepare the workplace. Designate a safety zone with a radius of at least 15 m from the workplace,
which will be inaccessible to unauthorised persons. Ensure that there are no obstacles around the workplace which could cause
the operator or machine to collide during work. Remove all loose lightweight objects from the workplace, which can be caught by
the spinning brush and cause damage to the machine or be ejected at high speed.
Power supply connection
The machine is supplied only with a short power cord. Use an extension cord for proper power supply. The extension cord should
have rubber insulation of at least the H05RNF type or polyvinyl (PVC) insulation of at least the H05VVF type.
Always use cords intended for outdoor use due to the nature of the machine work. The power cord should have a single socket
O R I G I N A L
I N S T R U C T I O N S
15
Publicidad
