Kemper 104987N Instrucciones Para El Montaje página 13

5. Make sure that the seals are in a good state before connecting the gas
cartridge.
6. Never use the appliance with damaged or worn seals.
7. Never use the appliance if it leaks, is deteriorated or malfunctioning.
8. Put the cartridge in its slot, placing the cut on its neck in correspondence
to the safety stop.
9. Place the lever connecting the cartridge on the "LOCK" position.
WARNING: the appliance is now ready for use. The positioning of
the lever on "LOCK" presupposes the immediate ignition of the
stove as the gas circuit is ready for gas supply. Do not leave the
appliance unattended and without flame with the lever positioned
on "LOCK".
WARNING: the openings at the base of the burner provide air for
combustion, they should never be obstructed.
WARNING: Closed the cartridge cover before lighting. Not closing the
cover can cause the cartridge to overheat.
10. Turn anticlockwise all the way the cock until it is positioned on
"IGNITION" where the piezo ignition will ignite the flame.
11. If the stove dose not light, turn the control knob back to "OFF" position
and repeat.
12. If after three failed attempts, the stove dose not light, turn the control
knob to the "OFF position and move the cartridge lever to the "UNLOCK"
position.
13. Open the cartridge cover and remove the cartridge, Shake the cartridge
to see if it is empty. If empty, replace the cartridge and repeat from point
9.
14. Regulate the flame according to your needs.
15. Warning: the device is not equipped with a safety system for the automatic closing gas (thermocouple).
SHUTTING DOWN THE APPLIANCE
1. To turn off the appliance, rotate clockwise the cock to the "OFF" position and wait until the flame is fully
extinguished before performing the next step.
2. Position the cartridge-connecting lever on the "UNLOCK" position and remove the gas cartridge from the
compartment.
3. Wait for the plate to cool before storing it.
4. When the appliance is not in use, it is mandatory to remove cartridge out of the appliance.
5. This unit can be kept inside only if the cartridge has been disconnected and removed from the appliance. If
you expect that the barbeque remains unused for a certain period of time, store it in its original packaging
and in an environment free from dust.
CHANGING THE CARTRIDGE
1. Check that burners are extinguished before disconnecting the gas cartridge. Be careful the gas cartridge
could be hot.
2. Ensure that the cartridge is empty before replacing it (shake it in order to hear the sound produced by the liquid).
3. Replace the cartridge outside and away from other people.
4. Make sure that the cock of the hot plate is CLOSED: cock on "OFF" position (clockwise rotation).
5. Check that the cartridge connection lever is on the "UNLOCK" position.
6. Open the cartridge holder lid and take out the cartridge.
7. Check that the seals are in a good state of maintenance.
Put the cartridge in its housing placing the cut on the cartridge's neck in correspondence to the safety stop.
8.
9. Position the connecting lever on the "LOCK" position.
CLEANING AND MAINTENANCE
Clean your equipment after EVERY USE. Do not use abrasive or flammable detergents, which may damage the
components of the unit and may cause a fire. Clean with a solution of warm water and soap.
NEVER USE THE PRODUCTS FOR OVEN CLEANING. CAUTION: All cleaning and maintenance operations,
should be made when the unit is cold and after removing the cartridge.
MAINTENANCE – REPAIR
All questions of the departments services must be formulated to: KEMPER – Via Prampolini 1/Q – Lemignano
di Collecchio (PR) – Italy – Tel. +39 0521 957111 – Fax +39 0521 957195 – www.kempergroup.it– info@kempergroup.it
There are some residual risks after the installation of the appliance that have to be considered:
Residual risks according to Regulation (EU) 2016/426 (annex 1, point 1.2):
DT Istr 104987N_11/21
RESIDUAL RISKS
13/72