Matco Tools MT3800 Manual De Instrucciones

WARNING
Study, understand and follow all instructions provided with this
product. Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible place.
INTENDED USE OF THE TOOL
This tool is intended to be used to set M4-M10 and 5/16-3/8"
aluminum and steel rivet nuts and stainless steel rivet nuts up to
1/4" (M6). Operate only at the required air pressure necessary. Do
not over-set rivet nuts. Do not use this tool outside of the designed
intent. Never modify the tools for any other purpose or use.
BEFORE USE
Before use, check the parts diagram and part number listing on
page 4-5 to make sure all parts are included. If any parts are missing
or damaged, please call your distributor.
PRODUCT INFORMATION
Heavy duty. Set up to 3/8" steel rivet nuts.
Wide application range. Includes mandrels and nosepieces in
M4, M5, M6, M8, M10, 1/4", 5/16" and 3/8" standard thread pitches.
Instant hydraulic action. Adjust pulling traction up to 2,680 lbs.
to set rivet nuts with the pull of a trigger; remove tool by operating
free spinning rear wheel.
SPECIFICATIONS
Traction Power: 2,680 lbs. (1,219 kgs)
Tool Stroke: 6.5mm
Air Consumption: 3 CFM
Work Capacity: up to 3/8" (M10) in aluminum & steel nuts
up to 1/4" (M6) in stainless nuts
Air Inlet: 1/4" PT
Weight: 3.59 lbs. (1.63 kgs)
DO NOT DISCARD – GIVE TO USER
3/8" AIR RIVET NUT SETTING KIT
Made in Taiwan
to Matco specifications
Page 1
1 YEAR LIMITED WARRANTY
The manufacturer warrants this product to the original user against
defective material or workmanship for a period of 1 year from the
date of purchase.
The manufacturer reserves the right to determine whether the part
or parts failed because of defective material, workmanship or other
causes. Failures caused by accident, alteration or misuse are not
covered by this warranty.
The manufacturer, at its discretion, will repair or replace product
covered under this warranty free of charge. Repairs or replacements
of products covered under this warranty are warranted for the
remainder of the original warranty period.
The manufacturer or its authorized service representatives must
perform all warranty repairs. Any repair to the product by
unauthorized service representatives voids this warranty. The rights
under this warranty are limited to the original user and may not be
transferred to subsequent owners.
The warranty is in lieu of all other warranties, expressed or implied,
including warranties of merchantability and fitness for a particular
purpose. Some states do not allow the exclusion or limitations of
incidental or consequential damages, so the above limitations may
not apply to you.
Authorized Matco Repair Centers:
United States
Matco Air Tool Repair SV
1330 Commerce Drive
Stow, OH 44224
(800) 433-7098
NMG Industrial WTRC
Attn: South Dock
2223 S. Wilson Street
Tempe, AZ 85282
Caution: To help prevent personal injury
Normal use of this product is likely to expose the user to dust and/
or microscopic particles containing chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Always wear appropriate safety equipment and clothing when
using this product. Study, understand and follow all instructions
provided with this product. Failure to read and follow all warnings
and operating instructions may result in damages and serious
injury or death.
• Always wear ANSI approved goggles when using this product
(users and bystanders).
• Never use this tool for any application other than for which
it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool, modification
of the tool or use of the tool with accessories not designed for it
could result in serious injury or death.
• Always select the correct accessories of the correct size and
design for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and adequately
equipped area.
• Do not begin repairs without assurance that vehicle is in secure
position and will not move during repair.
MT3800
Canada
H. T. Pneumatic Rebuilders Inc.
22 Goodmark Place
Units 7 & 8
Toronto, Ontario M9W6R2
1611285-14 MA