Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

IMPORTANT SAFETY INSTRUCTIONS
1.
SAVE THESE INSTRUCTIONS.
portant safety and operating instructions for the battery charger
MODEL BWC350. You may need to refer to these instructions at a
later date.
2.
CAUTION.
To reduce risk of injury, charge only lead-acid re-
chargeable batteries. Other types of batteries may burst causing
personal injury and property damage.
3.
Do not expose the charger to rain or snow if specifically warned on
the unit not to do so.
4.
Use of an attachment not recommended or sold by the battery
charger manufacturer may result in a risk of fire, electric shock, or
injury to persons.
5.
To reduce the risk of damage to the electric plug and cord, pull by
the plug rather than the cord when disconnecting the charger.
6.
Make sure the cord is located so that it will not be stepped on,
tripped over, or otherwise subjected to damage or stress.
7.
An extension cord should not be used unless absolutely necessary.
Use of an improper extension cord could result in a risk of fire and
electric shock. If an extension cord must be used, make sure:
a. That the pins on the plug of extension cord are the same number,
size, and shape as those of the plug on the charger;
b. That the extension cord is properly wired and in good condition; and.
c. If the length of the extension cord is less than 25 feet, use a 14AWG
cord, If 50 feet- 12AWG, 100 feet-10AWG, 150 feet-8AWG.
8.
Do not operate the charger with a damaged cord or plug, replace
them immediately.
9.
Do not operate the charger if it has received a sharp blow, been
dropped, or otherwise damaged in any way; take it to a qualified
serviceman.
10. Do not disassemble the charger; take it to a qualified serviceman
when service or repair is required. Incorrect reassembly may result
in risk of electric shock or fire.
11. To reduce the risk of electric shock, unplug the charger from the
outlet before attempting any maintenance or cleaning. Turning off
the controls will not reduce this risk.
12.
WARNING - RISK OF EXPLOSIVE GASES
a. WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGER-
OUS. BATTERIES GENERATE EXPLOSIVE GASES DURING
NORMAL BATTERY OPERATION. FOR THIS REASON IT IS OF
UTMOST IMPORTANCE THAT EACH TIME BEFORE USING
YOUR CHARGER, YOU READ THIS MANUAL AND FOLLOW THE
INSTRUCTIONS EXACTLY.
027-1038 Rev. 20170214
BATTERY CHARGER/ANALYZER
12/24 VOLT 70/35 AMP
13.
Made in USA
This manual contains im-
14.
15.
16.
b. To reduce the risk of battery explosion, follow these instructions and
those published by the battery manufacturer and manufacturer of any
equipment you intend to use in vicinity of the battery. Review cau-
tionary markings on these products and on the engine.
PERSONAL PRECAUTIONS
a. Someone should be within range of your voice or close enough to
come to your aid when you work near a lead-acid battery.
b. Have plenty of fresh water and soap nearby in case battery acid
contacts skin, clothing, or eyes.
c. Wear complete eye protection, and clothing protection. Avoid touch-
ing eyes while working near battery.
d. If battery acid contacts skin or clothing, wash immediately with soap
and water. If acid enter eyes, immediately flood eyes with running
cold water for at least 10 minutes and get medical attention
immediately.
e. NEVER smoke or allow a spark or flame in vicinity of the battery or
engine.
f. Be extra cautious to reduce risk of dropping a metal tool onto the
battery. It might spark or short circuit the battery or other electrical
parts that may cause an explosion.
g. Remove personal metal items such as rings, bracelets, necklaces,
and watches when working with a lead-acid battery. A lead-acid
battery can produce a short circuit current high enough to weld a
ring, or the like, to metal, causing a severe burn.
h. Use this charger for charging a LEAD-ACID battery only. It is not
intended to supply power to a low-voltage electrical system other
than in an automotive application. Do not use this battery charger for
charging dry-cell batteries that are commonly used with home appli-
ances. These batteries may burst and cause injury to persons and
damage to property.
i. NEVER charge a frozen battery.
PREPARING TO CHARGE
a. If necessary to remove battery from vehicle to charge, always re-
move the grounded terminal from the battery first. Make sure all
accessories in the vehicle are off, so as not to cause an arc.
b. Be sure the area around the battery is well ventilated while the bat-
tery is being charged. Gas can be forcefully blown away by using a
piece of cardboard or other non-metallic material as a fan.
c. Clean the battery terminals. Be careful to keep corrosion from com-
ing in contact with eyes.
d. Add distilled water in each cell until battery acid reaches level speci-
fied by the battery manufacturer. This helps purge excessive gas
from cells. Do not overfill. For a battery without cell caps, carefully
follow the manufacturer's recharging instructions.
e. Study all battery manufacturer's specific precautions such as remov-
ing or not removing the cell caps while charging and the recommend-
ed rates of charge.
f. Determine voltage of the battery by referring to the car owner's man-
ual and make sure that the output voltage selector switch is set at the
correct voltage. If the charger has adjustable charge rate, charge the
battery initially at the lowest rate.
CHARGER LOCATION
a. Locate the charger as far away from the battery as the DC cables
permit.
b. Never place the charger directly above the battery being charged;
gases from the battery will corrode and damage the charger.
c. Never allow battery acid to drop on the charger when reading the
specific gravity or filling battery.
d. Do not operate the charger in a closed-in area, or restrict ventilation
in any way.
e. Do not set a battery on top of the charger.
DC CONNECTION PRECAUTIONS
a. Connect and disconnect the DC output clamps only after setting the
charger switches to the OFF position and removing the AC cord from
the electric outlet. Never allow the clamps to touch each other.
b. Attach the DC clamps to the battery post and twist or rock back and
BWC350
1701024-11

Publicidad

loading

Resumen de contenidos para Matco Tools BWC350

  • Página 1 MODEL BWC350. You may need to refer to these instructions at a ances. These batteries may burst and cause injury to persons and later date.
  • Página 2 BWC350 BATTERY CHARGER/ANALYZER 12/24 VOLT 70/35 AMP forth several times to make a good connection. This tends to keep the outlet, have a proper outlet installed by a qualified electrician. the clamps from slipping off the terminals and helps to reduce the Improper connection can result in a risk of an electric shock.
  • Página 3 BWC350 BATTERY CHARGER/ANALYZER 12/24 VOLT 70/35 AMP DEEP DISCHARGE RECOVERY - If the charger determines a battery is b. For best results, the battery should be fully charged before being deeply discharged, it will attempt to recover the battery with a program used with the Electrical Stability System.
  • Página 4 BWC350 BATTERY CHARGER/ANALYZER 12/24 VOLT 70/35 AMP WIRING DIAGRAM 027-1038 Rev. 20170214 4  1701024-11...
  • Página 5 BWC350 BATTERY CHARGER/ANALYZER 12/24 VOLT 70/35 AMP PARTS LIST Item Description Part No. Front Leg ............605671 Axle w/nuts ............610052 Wheel w/nuts (2) ..........611157 Rectifier (-) ............611231 Transformer ............. 611232 Fan Blade ............610189 Fan Motor w/blade ........... 610190 DC Circuit Breaker ...........
  • Página 6 BWC350 CARGADOR / ANALIZADOR DE BATERÍA 12/24 VOLT, 70/35 AMP ZAR EL CARGADOR LEA ESTE MANUAL Y SIGA EXACTAMENTE LAS INSTRUCCIONES. b. Para reducir el riesgo de explosión de la batería, siga estas instruc- ciones y las publicadas por el fabricante de la batería y de cualquier equipo que utilice cerca de ella.
  • Página 7 BWC350 CARGADOR / ANALIZADOR DE BATERÍA 12/24 VOLT, 70/35 AMP todos los interruptores del cargador y de desenchufar el cable AC. diseñados para tal conexión. El enchufe debe estar conectado a una Nunca permita que las pinzas se toquen. toma que esté correctamente instalada y conectada a tierra de b.
  • Página 8 BWC350 CARGADOR / ANALIZADOR DE BATERÍA 12/24 VOLT, 70/35 AMP ción de una descarga profunda. ción; si la batería acepta la carga, empezará a cargarse. Para obte- ner mejores resultados, el interruptor de Tipo de Batería debe estar NOTAS: en No Sellada. Si la batería es de tipo sellado, entonces el interrup- DEMORA DE CUATRO SEGUNDOS –...
  • Página 9 BWC350 CARGADOR / ANALIZADOR DE BATERÍA 12/24 VOLT, 70/35 AMP DIAGRAMA DE CABLES 027-1038 Rev. 20170214 9  1701024-11...
  • Página 10 BWC350 CARGADOR / ANALIZADOR DE BATERÍA 12/24 VOLT, 70/35 AMP PARTES DE REPARACIÓN Articulo Descripcíon N. Pieza Pata Frontal ............. 605671 Barra con tuercas ..........610052 Ruedas con tuercas (2) ........611157 Rectificador (-) ..........611231 Transformador ..........611232 Hélice Del Ventilador ........610189 Motor Del Ventilador con aspas de ventilador .
  • Página 11 BWC350 CHARGEUR / ANALYSEUR DE BATTERIE 12/24 VOLT 70/35 AMP AVERTISSEMENT: DANGER DÛ AUX GAZ EXPLO- SIFS a. IL EST DANGEREUX DE TRAVAILLER PRÈS D'UNE BATTERIE AU PLOMB EN RAISON DES GAZ EXPLOSIFS PRODUITS LORS DU FONCTIONNEMENT NORMAL DE LA BATTERIE. POUR...
  • Página 12 BWC350 CHARGEUR / ANALYSEUR DE BATTERIE 12/24 VOLT 70/35 AMP a. Vérifier la polarité des bornes de la batterie. En général, la borne EMPLACEMENT DU CHARGEUR positive (POS, P, +) a un diamètre plus grand que celui de la borne a.
  • Página 13 BWC350 CHARGEUR / ANALYSEUR DE BATTERIE 12/24 VOLT 70/35 AMP augmenter le temps de charge de 25 pourcent. effectuer une épreuve de charge ou tester autrement les batteries récupérées pour déterminer si la capacité CCA se trouve à au moins NOTICE D’UTILISATION...
  • Página 14 BWC350 CHARGEUR / ANALYSEUR DE BATTERIE 12/24 VOLT 70/35 AMP SCHÉMA DE CÂBLAGE 027-1038 Rev. 20170214 14  1701024-11...
  • Página 15 BWC350 CHARGEUR / ANALYSEUR DE BATTERIE 12/24 VOLT 70/35 AMP LISTE DES PIÈCES DE RECHANGE Pièces Descrption N. de Pièce Pied avant ............605671 Axe avec écrous ..........610052 Roue avec écrous (2) ........611157 Redresseur (-) ..........611231 Transformateur ..........611232 Pale de Ventilateur ..........
  • Página 16 BWC350 BATTERY CHARGER/ANALYZER 12/24 VOLT 70/35 AMP Notes: Matco Tools Stow, Ohio 44224 www.matcotools.com 027-1038 Rev. 20170214 16  1701024-11...