KUNERT MATA Manual De Instrucciones página 9

WARNING Always use the restraint system.
The maximum wheel pressure is 0,8 BAR
The pram seat is equipped with a safety bar. It is mounted on the pram by sliding the hooks into the correct
slots on both sides of the seat, pressing at the same time red buttons in order to lock the safety bar. When
mounted, release the buttons (fig. 17). Always check whether the safety bar is mounted correctly. In order
to remove the safety bar, press the red buttons to release hooks on both sides of the pram and then pull
the safety bar up.
The pram is equipped with a 5-point safety harness. After placing the child on the pram seat, push the
buckles of the harness into the lock (fig. 18) and adjust the length of the straps by pulling them tight. To
unbuckle the harness, press on the sides of the buckle and pull them apart.
The seat is equipped with a cover that can be mounted with snaps on both sides of the booth (Fig. 19).
The pram is equipped with a rain cover which is pulled over it. The rain cover has ventilation outlets at the
level of the child's face.
The pram also comes with a car seat option for children. To mount the car seat, the car seat adapters need
to be mounted first to the chassis. To mount the adapters on the chassis, click them into designated slots
(two on each side of the pram) (fig. 20).WARNING! Before using the car seat, ensure that the car seat
adapters are correctly mounted. Both adapters should be locked. After correct mounting of the car seat
adapters on the chassis, you can move on to mounting the car seat. To mount the car seat, you need to fit
its buckles into matching plastic handles on the adapters (fig. 21).This pram does not substitute a cradle or a
crib. If your child needs to sleep, it is recommended to put him/her in an appropriate carrycot, cradle or crib.
The car seat comes with a hood and a cover which are mounted with snaps. The car seat is equipped with
an adjustable handle. The handle is adjusted by pressing the red buttons on both sides of the car seat and
moving the handle into a desired position (fig. 22).To remove the car seat, you need to pull the levers on
both sides of the car seat (fig. 23). To dismantle the adapters, press the buttons on the both sides of the
pram chassis. Car seats of the Kunert model: Carlo, Kent, Pixel and Trix are dedicated to this stroller model.
To adjust the handle height, you need to press the buttons on both sides of the handle and then adjust the
height while simultaneously pressing the buttons (fig. 24).
To mount the carrycot on the chassis, click it into designated slots (one on each side of the pram) (figs. 7)
until the hooks are locked. The hooks are locked automatically. Warning The carrycot should always be
mounted rear-facing (so that the child faces the person pushing the pram). To take the carrycot off, press
the adapter buttons on both sides of the pram (fig. 8) and lift the carrycot up using the handle.
The carrycot has a permanently attached hood. If necessary, the hood can be adjusted by sliding it up and
down (fig. 9). The hood has a handle which is used to carry the carrycot (fig. 10).
The carrycot is equipped with a cover which can be mounted using a zip and attaching the snaps of the
cover to the respective snaps on both sides of the hood (fig. 11).
MOUNTING AND REMOVAL OF THE PRAM SEAT
To mount the seat on the chassis, click it into designated slots (one on each side of the pram) (fig. 12) until
the hooks are locked .The hooks are locked automatically. The stroller seat may be mounted in front-facing
and rear-facing positions.
WARNING! Before you use the pram, make sure all blocking devices are activated.
To remove the seat, press the buttons on the both sides of the pram chassis (fig. 8).
SAFETY BAR
SAFETY HARNESS IN THE PRAM
PRAM COVER
RAIN COVER
MOUNTING THE CAR SEAT
HANDLE HEIGHT ADJUSTMENT
MOUNTING AND REMOVAL OF THE CARRYCOT
CARRYCOT HOOD
CARRYCOT COVER
9