Before you carry out any tasks on the device, trans-
port or store it, make sure that the direction of rotation
switch is in the middle position (lock). To prevent the
device from starting up unintentionally.
Attention - Service lines!
Danger! Take steps to ensure that you do not hit
upon any service lines (electricity, gas, water) when
working with electrical appliances. Check, if need be
with a service line detector, before you start to cut or
bore into a surface.
Information on the rechargeable battery
•
Please observe the operating manual for the re-
chargeable batteries.
Information on the charging unit and charging
process
•
Please observe the operating manual for the
charging unit.
Warning! This electric tool generates an electromag-
netic field during operation. This field can impair ac-
tive or passive medical implants under certain condi-
tions. In order to prevent the risk of serious or deadly
injuries, we recommend that persons with medical
implants consult with their physician and the manu-
facturer of the medical implant prior to operating the
electric tool.
Careful handling and use of battery devices
•
Charge the batteries only in chargers that are
recommended by the manufacturer. Risk of fire
if a charger that is suitable for a specific type of
battery is used with other batteries.
•
In the power tools, use only the batteries de-
signed for the purpose. The use of other batter-
ies may result in injuries and risk of fire.
•
Keep the unused battery away from paper
clips, coins, keys, nails, screws and other small
metal objects, which could cause bridging of
the contacts. A short circuit between the battery
contacts may cause burns or fire.
•
If used incorrectly, liquid may leak from the bat-
tery. Avoid contact with this. In the event of acci-
dental contact, rinse off with water. If the liquid
gets into eyes, seek medical assistance. Leaking
battery fluid may cause skin irritations or burns.
•
Ensure that the device is switched off before in-
serting the battery. Inserting a battery into a power
tool that is switched on may result in accidents.
•
Recharge the batteries indoors only because
the battery charger is designed for indoor use
only. Risk of electric shock.
•
To reduce the electric shock hazard, unplug the
battery charger from the mains before cleaning
the charger.
20 | GB
•
Do not subject the battery to strong sunlight over
long periods and do not leave it on a heater. Heat
damages the battery and there is a risk of explosion.
•
Allow a hot battery to cool before charging.
•
Do not open up the battery and avoid mechan-
ical damage to the battery. Risk of short circuit
and fumes may be emitted that irritate the respira-
tory tract. Ensure fresh air and seek medical assis-
tance in the event of discomfort.
•
Do not use non-rechargeable batteries. This
could damage the appliance.
7. Residual risks
The machine has been built according to the state of
the art and the recognised technical safety require-
ments. However, individual residual risks can arise
during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
• Residual risks can be minimised if the „safety in-
structions" and the „Proper use" are observed
along with the whole of the operating instructions.
• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet. Use the tool that is recommend-
ed in this manual.. This ensures that your machine
performs optimally.
• Hands may never enter the processing zone when
the machine is in operation.
8. Technical data
Cordless drill:
Nominal voltage:
Idle-running speed:
1st gear:
Idle-running speed:
2nd gear:
Punching power:
Max. torque:
Drill chuck
clamping range:
Weight:
Subject to technical changes!
Noise and vibration
m Warning: Noise at the workplace can exceed 85
dB (A). In this case, noise protection measures are
necessary for the user (wear hearing protection!).
www.scheppach.com
20 V
max. 0 - 450 min
-1
max. 0 - 1600 min
-1
0 - 25600 bpm
45 Nm
max. 13 mm
1,3 kg