Publicidad
Idiomas disponibles
Idiomas disponibles
Fig. P
Cold Weather Operation
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply before
making any adjustments or removing/installing
attachments or accessories. An accidental
actuation can cause injury.
WARNING: Do not store tools in a cold weather
environment to prevent frost or ice formation on the
tools operating valves and mechanisms that could
cause tool failure.
WARNING: Some commercial air line drying
liquids are harmful to "O"-rings and seals – do
not use these low temperature air dryers without
checking compatibility.
When operating tools at temperatures below freezing:
1. Make sure compressor tanks have been properly
drained prior to use.
2. Keep tool as warm as possible prior to use.
3. Make certain all fasteners have been removed
from magazine.
4. Lower air pressure to 80 p.s.i.g. (5.7 kg/cm
5. Reconnect air and and load nails into magazine.
6. Actuate the tool 5 or 6 times into scrap lumber to
lubricate "O"-rings.
7. Turn pressure up to operating level (not to exceed
120 p.s.i.g. [8 kg/cm
2
]) and use tool as normal.
8. Always drain the compressor tanks at least once a day.
Hot Weather Operation
Tool should operate normally. However, keep tool out
of direct sunlight as excessive heat can deteriorate
bumpers, o-rings and other rubber parts resulting in
increased maintenance.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply before
making any adjustments or removing/installing
attachments or accessories. An accidental
actuation can cause injury.
Accessories
WARNING: Since accessories, other than those
16
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be
used with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
Versatrack™ (Fig. Q)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply before
making any adjustments or removing/installing
attachments or accessories. An accidental
actuation can cause injury.
WARNING: To reduce the risk of serious personal
injury, do not use a damaged Versatrack™ hang hook
or Versatrack™ Trackwall. A damaged Versatrack™
hang hook or Versatrack™ Trackwall will not support
the weight of the tool.
WARNING: To reduce the risk of serious personal
injury, ensure the fitting holding the hang hook
is secure.
WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or suspend
objects from the hang hook. ONLY suspend tool on the
Versatrack™ Trackwall using the hang hook.
WARNING: Ensure that the tool weight does not
) or less.
2
exceed the maximum rated weight for the selected
Versatrack™ hook.
WARNING: When hanging objects on a Versatrack™
Trackwall rail, adequately space the tools in order to
not exceed 75 lb (35 kg) per linear foot.
iMPORTAnT: Versatrack™ accessories mount compatible
tools securely to the Versatrack™ Trackwall system.
1. Turn tool off, remove air supply and remove accessories.
CAUTION: Any product with exposed cutting teeth
must have them covered securely if it is to be on
the Versatrack™ Trackwall.
2. Attach the hang hook
a. Use a wrench to remove the fitting
b. Place the Versatrack™ hang hook on the fitting.
c. Use a wrench to re-install the fitting at the base of
the tool.
nOTE: Versatrack™ accessories for use with your tool are
available at extra cost from your local dealer or authorized
English
on the tool.
17
.
3
9
Publicidad
