Descargar Imprimir esta página

Stanley PPRH5KL Manual De Instrucciones página 6

Fuente de energía profesional

Publicidad

Idiomas disponibles

Idiomas disponibles

area LigHt
The built-in 3-LED area light located on the back of the unit is controlled by the area light on/off button on the front panel (refer to
the Features section to locate). Press the area light on/off button once to turn the light on. Press the area light on/off button again
to turn the area light off. Make sure the area light and the unit are turned off when the unit is being recharged or stored.
Periodically check the unit' s battery status by pressing the battery power level button. (Two red and one green battery status
indicator lights indicate a full battery. Only one red battery status indicator lights indicates that the unit needs to be recharged.)
POrtaBLe COMPressOr
The built-in 12 volt DC compressor is the ultimate compressor for all vehicle tires, trailer tires and recreational inflatables. The
compressor hose with connector (chuck) is stored in the compressor hose storage conpartment. The compressor on/off switch is
located on the front panel of the unit to the right of the air pressure gage (refer to the Features section to locate). The compressor
can operate long enough to fill up to 3 average sized tires before the battery must be recharged.
The compressor may be used by removing the air hose from the storage compartment and, if required, fitting an appropriate nozzle
to the air hose. Return hose to the storage compartment after use.
WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: FOLLOW ALL SAFETY INSTRUCTIONS FOUND
IN THE "SPECIFIC SAFETY INSTRUCTIONS FOR COMPRESSORS" SECTION OF THIS INSTRUCTION MANUAL.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
Do not operate compressor continuously for extended periods of time (approximately 10 minutes, depending on ambient
temperatures), as it may overheat. In such event, compressor will automatically shut down. Immediately press the compressor on/
off button to turn the compressor off. Restart after a cooling down period of approximately 30 minutes.
inflating tires or Products with valve stems
1. Place connector (chuck) on valve stem.
2. Ensure connector is pushed on to valve stem as far as possible before closing thumb latch.
3. Make sure latch is secure.
4. Turn on the compressor power switch.
5. Check pressure with the pressure gage.
6. When desired pressure is reached, open thumb latch and remove connector from valve stem.
7. Turn off compressor power switch.
8. Allow unit to cool before storing away.
9. Store compressor hose and connector (chuck) in storage compartment.
inflating Other inflatables without valve stems
Inflation of other items requires use of one of the adapters (nozzles).
1. Select the appropriate nozzle, located on the inside back cover.
2. Insert appropriate adapter (i.e. needle) into connector (chuck) and close thumb latch.
3. Insert adapter (i.e., needle) into item to inflate to appropriate pressure.
4. Turn on the compressor power switch — inflate to desired pressure or fullness.
IMPORTANT NOTE: Small items such as volleyballs, footballs, etc. inflate very rapidly. Do not over-inflate.
5. Remove adapter.
6. Switch the Compressor Power Switch off.
7. Allow unit to cool before storing away.
8. Store compressor hose and connector (chuck) in storage compartment.
Care aND MaiNteNaNCe
All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit is not in use, we
recommend that the battery is charged at least every 30 days.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the unit with a soft cloth moistened with a mild
solution of water and detergent.
There are no user-replaceable parts. Periodically inspect the condition of adapters, connectors and wires. Contact manufacturer to
replace any components that have become worn or broken.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Service life is dependent on a number of factors including but not limited to
the number of recharge cycles, and proper care and maintenance of the battery by the end user. Contact manufacturer for any
information you may need.
PPRH5KL_ManualENSP_050813.indd 10-11
10
SAFE BATTERY DISPOSAL
Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed of properly. Recycling is
required, contact your local authority for information. Failure to comply with local, state and federal regulations can
result in fines, or imprisonment.
Contact your local waste management authority to dispose of this product.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result
in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
12 volt DC charger plug fuse replacement (may be sold separately)
The fuse in the plug end of the 12 volt DC charger protects the adapter' s charging circuit. If the 120 volt AC charger operates, but the DC
charging adapter does not, then this fuse may be opened (blown).
To replace the fuse:
1. Unscrew the end cap of the DC plug (counterclockwise).
2. Remove spring center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate a replacement 8 amp volt fuse.
5. Replace the fuse, spring, contact and end cap.
6. Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.
7. Test for proper operation of the 12 Volt DC Charging Adapter.
trOuBLesHOOtiNg
Unit will not charge
• Make sure the inverter power switch is in the off position.
• Make sure a suitable gage extension cord is properly connected to both the unit and a functioning AC outlet.
• Make sure the 12 volt DC charger is properly connected to both the unit and a functioning DC power source.
Unit fails to jump-start
• Make sure unit' s jump-starter power switch is in the on position.
• Check that unit has a full charge. Recharge unit if necessary.
• Make sure a proper polarity cable connection has been established.
120 volt AC outlet will not power appliance
• Make sure the inverter power switch is in the on position.
• Make sure you have followed all the steps in the 120 AC portable power supply instructions carefully.
• Refer to the important notes included in that section that explain common problems and solutions.
• Check that unit has a full charge. Recharge unit if necessary.
12 volt DC accessory outlet will not power appliance
• Make sure the the appliance does not draw more than 5 amps.
• Check that unit has a full charge. Recharge unit if necessary.
USB power port will not power appliance
• Make sure the USB power button is in the on position.
• Check that unit has a full charge. Recharge unit if necessary.
LED area light does not come on
• Make sure the area light on/off button is in the on position
• Check that unit has a full charge. Recharge unit if necessary.
Portable Compressor will not inflate
• Make sure the compressor power switch is in the on position.
• Check that unit has a full charge. Recharge unit if necessary.
• Make sure connector (chuck) is pushed to valve stem and thumb latch is closed when attempting to inflate tires; or nozzle
(adapter) is securely inserted into connector (chuck) on all other inflatables.
• The compressor may be overheated. Press the compressor on/off button to turn the compressor off. Restart after a cooling down
period of approximately 30 minutes.
PLEASE
RECYCLE
or
11
5/8/2013 10:28:39 AM

Publicidad

loading