Sthor 78127 Manual página 18

GB
on the temperature of storage, since the higher the temperature, the fastest the process. In case of incorrect storage of batteries,
there is a danger of electrolyte leakage. In case of leakage, it is required protect the leakage with neutralizing agent. In case of
contact of electrolyte with the eyes, it is required to rinse the eyes abundantly, and then immediately seek medical assistance. It
is prohibited to use a tool with a damaged battery.
In case the battery is completely worn out, it is required to deposit it at a special point dedicated to disposal of such waste.
Transport of the batteries
Lithium-ion batteries are in accordance with legal regulations treated as dangerous waste. The user of the tool may transport the
tool with the battery or only batteries by land. Then no additional conditions must be complied with. In transport is realised by third
parties (for example dispatch through courier service), then it is required to proceed in accordance with regulations for transport
of dangerous materials. Before shipment, contact an authorised person.
It is prohibited to transport damaged batteries. During transport the battery must be removed from the tool, and the exposed
contacts protected, e.g. with insulating tape. Protect the batteries so that they do not move inside the package during transport. It
is also required comply with the national regulations for transport of dangerous materials.
Charging the battery
Note! Prior to charging, unplug the charger of docking station from the mains, by pulling off the plug of the charger from the mains
socket. Also clean the battery and its terminals of dirt and dust using soft and dry cloth.
Disconnect the battery from the tool by pressing the latch or both latches at the same time, and then slide it out from the battery
socket.
Plug the charger to battery's socket (II)
Plug the charger to mains.
The diode lights up which indicates the start of charging process.
After charging is fi nished, the diode changes its colour from red to green, which indicates power supply to the charger.
Pull off the charger plug from the mains socket, and the plug of the charger cable should be disconnected from the battery.
Attention! If, when the charger is connected to the power supply, the green LED is on, this indicates a fully charged battery. In this
case, the charger does not start charging.
INSTALLATION OF ACCESSORIES
NOTE! All actions mentioned in this chapter should be carried out with supply voltage off - the battery must be disconnected from
the tool!
Installation of accessories in tool chuck (III)
Press the lock button. In the case of installing accessories in the chuck of fl exible arm, movement of a spindle is locked by pressing
the spindle lock button.
Turn the spindle until it is locked.
Unscrew the drill chuck nut.
Install the necessary accessory in the tool chuck.
Tighten the nut so that the accessory is fi rmly and securely fastened in the tool chuck.
Disassemble accessories in the reverse order.
Adjustment of rotational speed (IV)
Rotational speed can be adjusted by turning the knob. The larger number is visible on the knob, the higher is rotational speed.
USE OF GRINDER
Basic precautions should be taken when using abrasive discs. Before each use, inspect the abrasive discs for damage and defor-
mation. It is forbidden to use abrasive discs in which any damage has been found. Do not throw, hit the abrasive discs or abruptly
apply them to the workpiece. This may cause the abrasive disc to fall to pieces and thus cause severe injuries.
The shaft of accessory must not protrude more than 5 - 15 mm from the tool chuck. Do not use any accessory with a shaft longer
than 45 mm.
Accessories to be used as per their intended use. For example, do not use grind using cutting discs, do not use drill bits for side
milling.
Before installing any accessory, set the operating speed appropriate for particular type of equipment. After the installation, allow
reaching the full working speed. Only accessories rotating at full speed may be applied to the workpiece. Do not use excessive
force, just what is needed for proper operation. Grinding wheels to be applied to the workpiece at small angle. Cutting discs to
be applied to the intended saw cut perpendicularly. Brushes to be applied in such a way so that the wire ends do the processing,
O R I G I N A L I N S T R U C T I O N S
18