Stanley STHR1232 Manual De Instrucciones página 14

14 • ENGLISH
Installing an accessory (Fig. C)
f Clean and grease the shank (10) of the accessory.
f Pull back the SDS chuck (5) and insert the shank (10)
into the chuck.
f Push the accessory down and turn slightly until it fits
into the slots.
f Pull the accessory to check that it is properly adjusted.
The hammer drilling function requires the accessory
can move axially several centimeters when placed in
the holder.
f To remove the accessory, pull back the chuck SDS (5)
and remove the accessory.
Installing an chuck adapter for regular drill bit
(Fig. D and E)
f Clean and grease the shank (11) of the chuck adapter.
f Pull back the SDS chuck (5) and insert shank of the
chuck adapter (11) into the SDS chuck (5).
f Push down the chuck adapter and turn it slightly until it
fits into the slots.
f The key (12) tightening the chuck (13) to secure the
fixation of the drill (14).
f To remove the chuck adapter, pull the chuck back (5)
and remove the adapter.
USE
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check
for the location of wiring and pipes.
Warning! Do not apply chisels when the tool is in the
drilling mode.
Light Indicators (Fig. F)
f Green: Power light (15), indicates that the tool is
connected.
f Red: Carbon warning light worn out (16), tells the user
to do a change of carbons.
Selecting the operating mode (FIG. D)
The tool can be used in three modes: Rotary Hammer,
Chiseling, Rotary.
f To operate the drilling mode selector (4), rotate it
towards the required position, as indicated by the
symbols.
f To operate the operating mode selector (4), push the
unlock button (17) and rotate the selector towards the
required position, as indicated by the symbols.
DRILLING
Drilling and screwdriving
f For drilling steel, wood and plastics, and for screwdriving,
set the operation mode selector (4) to position
and drilling mode selector (8) in position
Drilling in masonry and concrete
f For hammer drilling in masonry and concrete, set the
operating mode selector (4) to the
the drilling mode selector (8) to the
f When hammering, the tool should not bounce and run
smoothly. If necessary, increase the speed.
Chiselling and roughing
f For hammering with spindle lock, and for light
chiselling and chipping, set the operating mode
selector (4) to the
selector (8) to the
f When changing from hammer drilling to chiselling, turn
the chisel to the desired position. If resistance is felt
during mode change, slightly turn the chisel to engage
the spindle lock.
ACCESSORIES
The performance of your tool depends on the accessory
used. STANLEY and Piranha accessories are engineered
to high quality standards and designed to enhance the
performance of your tool. By using these accessories you
will get the very best from your tool.
MAINTENANCE
Your STANLEY corded/cordless appliance/tool has
been designed to operate over a long period of time with
a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular
cleaning.
Warning! Before performing any maintenance on
corded/cordless power tools:
f Switch off and unplug the appliance/tool.
f Regularly clean the ventilation slots in your appliance/
tool/charger using a soft brush or dry cloth.
f Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
f Regularly open the chuck and tap it to remove any
dust from the interior (when fitted).
PROTECTING THE ENVIRONMENT
.
position and the drilling mode
position.
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your STANLEY
product needs replacement, or if it is of no further
use to you, do not dispose of it with household
waste. Make this product available for separate
collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
position and
position.