Publicidad
Idiomas disponibles
Idiomas disponibles
When turning on the motor:
•
Keep your feet away from the cutting tools.
–
Do not tilt the machine.
–
Do not stand in front of the discharge opening.
–
Never let your hands or other part of the body or
–
clothing place near moving parts.
Electrical safety
Check the connector plug on the machine fits into the
•
socket before use.
Never modify the connector plug.
•
Do not abuse the cord. Never use the cord for carrying,
•
pulling or unplugging the machine. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
Check the extension cable regularly for damage to the
•
insulation. Replace it if damaged.
If the connecting cable is damaged, withdraw the mains
•
plug immediately. A damaged cable may cause contact
with live parts and electric shock.
Never use damaged cord.
•
Keep the cord and extension cable away from cutting
•
tools and wheels. Cutting tools may damage the cable
and cause electric shock.
When using the machine outdoors, always use a
•
residual current-operated circuit-breaker (RCD) with an
operating current of 30 mA or less.
Use only extension cable for outdoor use with splash-
•
proofed connector. Its cross-section must be at least
for cable lengths up to 25m, and 2.5 mm
1.mm
cable lengths over 25m.
The machine should be connected only to a power
•
supply of the same voltage as indicated on the
nameplate, and can only be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Avoid body contact with earthed or grounded surfaces
•
(e.g. pipes, radiators, ranges, refrigerators).
Operation
Avoid operating on wet grass. Take particular attention
•
when working on wet grass to prevent slipping.
Hold the handle firmly with both hands during operation.
•
Keep the handle dry and clean to prevent accidents.
Do not run. Only walk during operation.
•
Pay particular attention to your footings when working
•
on a slope.
Do not work straight up or down on a slope. Always
•
work along horizontal line.
Be especially careful when turning the machine on a
•
slope.
Never work on a steep slope.
•
Pay extreme attention when reversing or pulling the
•
machine towards you.
Do not overreach. Keep proper footing and balance at
•
all times. This enables better control of the machine in
unexpected situations.
Always remember:
•
Keep your feet away from the cutting tools.
–
Do not tilt the machine.
–
Do not stand in front of the discharge opening.
–
Never let your hands or other part of the body or
–
clothing place near moving parts.
Do not force the machine. It does the job better and
•
safer at the rate for which it was designed. Frequent
overload may cause motor damage or fire.
https://tm.by
Интернет-магазин TM.by
Switch off the motor and unplug:
•
Whenever leaving the machine unattended
–
Before clearing a blockage or any fault
–
Before checking, cleaning or working on the
–
machine
Before making any adjustments, changing
–
accessories or storing
When the machine hits a foreign object. Wait until
–
the machine cools down. Inspect the machine
and replace the parts if needed before continuing
operation
Whenever the machine starts vibrating or making
–
noise unusually
When attaching or removing grass catcher
–
When someone enters your working area
–
When crossing surface other than grass
–
–
When transporting.
Stop the cutting tool:
•
If you have to tilt the machine
–
When crossing surfaces other than grass
–
Transporting the machine to and from surfaces
–
to be worked.
Pay attention to the cutting tools. They do not stop
•
immediately after switch off.
Maintenance instructions
Have your machine serviced by our authorized service
•
center, always using only genuine replacement parts.
Incorrect repair and poor maintenance can shorten the
for
life of the machine and increase the risk of accidents.
Inspect the machine on regular base.
•
Before servicing, inspection, adjustment, storage, or to
•
change an accessory, take following steps:
Shut off the power source
–
Disconnect the machine from power supply
–
Make sure that all moving parts have come to a
–
complete stop
Allow the machine to cool.
–
Inspect on the machine for possible damage:
•
Whether safety devices works properly for its
–
intended function
Whether all the moving parts work smoothly and
–
adequately
Whether all parts are not damaged and properly
–
installed
Check the cutting tool for any damage, worn or
–
unbalance
Check the grass catcher regularly for any
–
damage or worn
Check all the nuts, bolts and screws are tight
–
Replace or repair by our authorized service
–
center if there are any damaged or worn parts.
Do not carry out maintenance or repair work other than
•
that described in this instruction manual. Any other
work must be carried out by Makita authorized service
center.
Only use original Makita replacement parts and
•
accessories intended for your machine. Otherwise
it may result in personal injury or damage on the
machine.
Store the machine in a dry room. Keep it out of reach of
•
children. Never store the machine outdoors.
Publicidad
