Publicidad
Idiomas disponibles
Idiomas disponibles
Before using your new Automotive alarm, please read the
following recommendations.
IMPORTANT
•
Do not attempt to open this device; doing so could lead to malfunctions in
•
the device and the annulment of the warranty.
•
Do not use or store this device anywhere it might get wet.
•
Do not use this device in extreme temperatures.
•
If you do not have knowledge on the installation of automotive alarms,
•
make sure to go to a professional.
•
Always use a clean, soft, and dry rag in order to clean this device.
FEATURES
Your new STEREN automotive alarm is perfect for people that require a
trustworthy security system for their cars. This device has all the
necessary components for its installation. This way your car will be
completely safe against potential robbery. This alarm has several
characteristics for the safety of your car and the included keychain remote
control is ideal for keeping your car safe.
•
Automatic arm
•
Silent mode
•
Automatic locks controlled by ignition
•
Electric trunk opening
•
Ignition shut-off
•
Valet mode
•
6 tome siren
CONTROLS
1.- While the car is off
Activates the alarm / search through
a tone and LED blinking
2.- While the car is on
Automatically closes the doors.
While the car is off
Deactivates the alarm
3.- While the car is on
Opens the doors automatically
While the car is off
Activates silent mode / search through LED
blinking
4.- While the car is on
Activates the panic alarm
While the car is off
Activates anti-assault mode
ENGLISH-01
1
2
3
4
INSTRUCTIONS
HOW TO PROGRAM THE TRANSMITTER
1. Press the restart button and set the power switch on the car to the ON
position.
2. Insert the 10 pin connector to the main unit in order to turn it on.
3. You will hear 4 beeps and the LED indicator light will blink indicating that
you have entered programming mode.
4. In a lapse of no more than 30 seconds, press the "1" button on the
transmitter.
5. The main unit will synchronize with the receiver and the siren will emit a
beep.
6. In order to program the second transmitter, press the "1" button on the
second transmitter.
7. Once the main unit synchronizes with the receiver, you will hear two
beeps.
You can program up to 4 transmitters.
ARMING
Press the "1" button on the transmitter once and you will hear a beep. The
lights will begin to blink indicating that you are in armed mode.
Once the alarm has been armed, the deactivated power circuit will
instantaneously activate and the LED indicator light will slowly blink.
SILENCING THE ALARM
While the alarm is activated in armed mode, press the "1" button in order
to deactivate it. Even when the alarm is silenced, the system will remain in
armed mode.
SILENT ARMING
Press the "3" button on the transmitter, the lights will blink once in order to
confirm that you have entered silent armed mode.
This function is recommended for systems using the alarm pager
accessory.
In this mode, if any interferences in the vehicle occur, a signal will be
transmitted to the "pager" and the lights will blink for 30 seconds.
If the ignition switch is accessed, this will make the "pager" and the alarm
activate.
HOW TO DISARM THE ALARM SYSTEM
Press the "2" button once, the siren will emit two beeps and the lights will
blink three times. The alarm system will be deactivated.
For security purposes, while the system is disarmed and the ignition switch
is in the on position, only the open and close functions are activated along
with the anti-theft system, the rest of the functions will be deactivated.
AUTOMATIC RE-ARMING
If you do not open a door in the lapse of 20 seconds, the system will
automatically re-activate.
You will hear a beep and the indicator lights will blink once in order to
confirm that you have entered re-armed mode.
AUTOMOBILE SEARCH
1. While in armed mode, press the "1" button on the transmitter, the siren
will sound once and the lights will blink once.
2. Press the "4" button in order to activate the panic function.
3. Once you have identified your vehicle, press the "2" button in order to
deactivate the panic function.
4. Press the "3" button, the lights will blink once.
ANTI-THEFT SYSTEM
In order to test this function, follow these steps:
1. While the system is armed and the ignition switch is in the on position,
press the "4" button.
2. The lights and the LED indicator light will blink for 10 seconds. During
this 10 second period, press the "4" once more in order to enter anti-theft
mode.
3. Once the system has been activated, the LED indicator light will blink for
30 seconds. Afterwards, the siren will activate and the lights will begin to
blink.
ENGLISH-02
Publicidad
