YATO YT-85003 Manual De Instrucciones página 17

GB
line with a metal wire or string. The use equipment other than those specifi ed may result in a serious threat to the safety of the
operator and bystanders. Before mounting the cutting element and the cover, you should make sure that they are not damaged,
do not have cracks, they are not bent. Make sure that on the metal blade you do not see the rust, and the spool has at least 1
meter of cutting line.
During operation, it is likely, that objects can be thrown towards the operator and bystanders. The operator is responsible for ac-
cidents or a threat presented to others or to the environment. Do not work with device, if there are bystanders, especially children.
Before starting the work you should assign a safety zone with a radius of at least 15 metres away from the place of work.
Always wear eye and face shields, it protects your eyes, face and respiratory tract against dust, exhaust, and objects, which are
thrown out while cutting. Always wear appropriate, fi tting to the body, protective clothing. Use only long trousers. Do not wear loose
clothing or jewelry, because it can be caught by moving parts of the tool. Wear protective gloves and hearing protection. Wear
protective footwear with non-slip soles, do not work barefoot or in sandals. Always wear a protective helmet while working.
The device must be regularly reviewed in accordance with the information contained in the following section. This will allow for
more effi cient and safer operation.
Take special care when handling the fuel. It is fl ammable, and its vapors are explosive. Please observe the following recom-
mendations.
- Only use the canisters, which are designed for the fuel.
- Never remove the fuel fi ller cap nor add fuel when the engine is running. Before tanking wait until the engine and the exhaust
system components cool down.
- Do not smoke.
- Never refuel indoors.
- Never store the device or fuel canister in rooms with open fi re, for example near the water heater.
- Do not attempt to start the engine, if the fuel is spilled out, before you start device move it away from spilling.
- After refueling always shut and carefully tighten the fuel tank cap.
- Possible emptying the fuel tank must be done outside of the room.
If the blade strikes any foreign object or the device starts to vibrate or make noise in an unusual way, turn off the engine and wait
until the elements of hedge shear will stop. Disconnect the wire from the spark plug and take the following steps:
- inspect the damage,
- check whether there are any loose parts and tighten them,
- repair or replace any damaged parts for parts in accordance with the specifi cations.
When you work you should use hearing protectors. Exposure to excessive noise can lead to permanent hearing damage.
Use protective glasses. During the work the garbage can create risk of eye injury.
You must be familiar with the instructions to switch off the device in case of emergency.
Before use of the device, always check that the cutting element, screws, covers, and other items are not worn or damaged. Re-
place worn parts before starting work. You should also check that the screw connections not loosened. Tighten the loose bolts.
OPERATION
Do not start the work while you are tired, sick or under the infl uence of alcohol or other narcotic drugs.
It is forbidden to work with the grass trimmer indoors. The exhaust gases contain poisonous gases, their inhalation may be
dangerous for your health and life.
It is forbidden to expose the device to eff ect atmospheric precipitation and use it in an atmosphere of high humidity. It is also
forbidden the use of the device in an atmosphere with an increased risk of fi re or explosion.
Work only in daylight or in good artifi cial light.
If possible, avoid mowing wet grass.
Make sure that the legs always stand fi rmly on the slopes. Do not run with the grass trimmer, just walk. Do not mow on excessively
inclined slopes. When mowing on slopes you should move across slope, never up or down.
Use fuel and oil free from any contamination and intended for two-stroke engines. It is recommended to use only the high quality
products. This extends the life of engine.
During the operation, avoid contact with grounded, conductive, and non-isolated objects such as pipes, radiators, or refrigerators.
Do not cover the ventilation inlets and outlets. Even when the grass trimmer is not working.
It is forbidden to touch the engine, which heat up during operation, you could be burned.
Always wear appropriate, fi tting to the body, protective clothing. Wear protective gloves and hearing protection.
Always operate the grass trimmer by holding it with both hands. During operation hold the grass trimmer in such a manner that the
plane of rotation of the cutting element is always parallel to the ground. It is forbidden to tilt the grass trimmer and lift it excessively.
Adopt such position at work that there would be no need to draw hands for a full length.
Equipment handles must be kept clean and free of any oils or greases.
In a case when you notice any damaged or broken parts of the grass trimmer you should stop the work nor to start it.
. Damaged parts must be replaced before the starting of work.
The grass trimmer must be used assist is intended, cutting line should be used only to cut the grass. The blade can cut shrubs
and woody shoots of plants. It is forbidden to use the grass trimmer for other purposes, such as for trimming hedges, pruning
trees, shearing grain.
O R I G I N A L I N S T R U C T I O N S
17