Publicidad
Idiomas disponibles
Idiomas disponibles
Controls
Appearance may vary by model.
Empty
High
Low
On
Smart Dry
Fan
Power
Speeds
Controls
NOTE: When the bucket is full or removed, the controls
cannot be set.
1. Power Pad
Press to turn the dehumidifier on and off.
NOTE: Turning off the power by pressing the Power button
does NOT disconnect the appliance from power supply.
2. Fan Speed Pad
Controls the fan speed.
Press to select either High, Low, or Smart Dry fan speed.
Set the fan control to High for maximum moisture removal.
When the humidity has been reduced and quiet operation is
preferred, set the fan control to Low. Smart Dry compares
the set humidity level with the actual humidity and adjusts
the fan speed automatically.
3. Display
Shows the set % humidity level while setting, then shows the
actual (+/– 5% accuracy) room % humidity level.
4. Humidity Set Control Pads
The humidity level can be set within a range of 35%
RH (Relative Humidity) to 80% RH (Relative Humidity) in 5%
increments or in Nonstop mode for continuous operation. To
set the unit for continuous operation, press the "–" pad until
the "Nonstop" indicator light is illuminated.
NOTE: If Nonstop is selected, the dehumidifier will operate
continuously at its maximum dehumidification settings if
attached to a hose to drain or until the bucket is full. For
drier air, press the "–" pad and set to a lower percent value
(%). For damper air, press the "+" pad and set to a higher
percent value (%). When you first use the dehumidifier,
set the humidity control to 45% or 50%. Allow at least 24
hours for the dehumidifier to achieve the humidity level.
If you still have damper air than desired, set the humidity
level to a lower setting or select Nonstop for maximum
dehumidification.
5. Filter Reset
After 250 hours of operation, the Clean the Filter indicator
light will glow to remind you to clean the filter. Remove the
filter and clean it.
4
Nonstop
Humidity %
Press and hold Filter button for 3 seconds to reset the filter
reminder. See the Care and Cleaning section.
6. Timer Off
While the dehumidifier is operating, press the Timer button.
Press the "+" / "–" buttons to select the number of hours
you want the dehumidifier to continue to operate before
turning Off.
NOTE: After displaying the time, the Display will revert to
showing the current humidity after 5 seconds have passed.
Pressing the Timer button will display the number of hours
left on the Timer.
Timer On
While the dehumidifier is off, press the Timer button.
Press the "+" / "–" buttons to select the number of hours
you want the dehumidifier to remain off before turning On.
NOTE: The display will show the number of hours left until
the dehumidifier turns on.
To cancel the Timer:
Press the Timer button once, the hours remaining on the
Timer will appear on the display. Press the Timer button
against and the Timer will be cancelled.
7. Pump (on some models)
Activates the internal pump. Press Timer for 3 seconds
to activate the internal pump for automatic removal of
condensate. The Pump On light will remain illuminated after
3 seconds. Press Timer again for 3 seconds to deactivate
the pump. Before turning on the pump, ensure the included
hose is connected.
8. Empty Indicator
The "Empty" indicator will blink when the bucket is ready
to be emptied, or when the bucket is removed and/or not
replaced in the proper position.
9. WiFi (on some models)
Hold the Filter Reset button for 3 seconds to enable
connection of the dehumidifier to home WiFi .
Download SmartHQ App for details at:
GEAppliances.com/connect.
Pump On
On
Off
Filter
Filter
Timer
Reset
Hold 3 Sec For
Hold 3 Sec For
WiFi
Pump
49-5000764 Rev. 0
Publicidad
