SNOWJOE sunjoe 24V-HCS-LTE-P1 Manual Del Operador página 13

11. Use extreme caution when cutting brush and saplings.
The slender material may catch the saw chain and be
whipped toward you or pull you off balance.
12. When the saw chain is running, place the base plate on
the surface of the workpiece and let the saw cut on its
own. Apply only light pressure to the saw.
NOTE: The base plate helps to stabilize the saw and even
the material that being cut. It can also reduce the vibration
of the saw significantly. The base plate also acts like the
fulcrum for deep cuts because it raises the back end of
the saw. Using the base plate like a pivot point allows you
to go deep in the material with precise control.
13. Stop the motor and remove the battery from
the compartment:
– Whenever you leave the machine unattended;
– Before cleaning, checking or servicing the machine;
– After striking a foreign object. Inspect the machine
for any damage and make repairs before restarting
it again;
– If the machine begins to vibrate abnormally,
immediately look for the cause of the vibrations
and have the machine inspected at an authorized
Snow Joe + Sun Joe
®
+ Sun Joe customer service center at
®
1-866-SNOWJOE (1-866-766-9563) for assistance;
– When the machine is not in use.
IMPORTANT! Always remember that an incorrectly used
pruning saw may disturb others and have a serious impact on
the environment.
To respect people and the environment:
• Avoid using the machine in environments or at times of the
day when it may disturb others.
• Scrupulously comply with local regulations and provisions
for the disposal of waste materials after sawing.
• Scrupulously comply with local regulations and provisions
for the disposal of oils, damaged parts or any elements
which have a strong impact on the environment.
• A certain amount of chain lubricating oil is released into
the environment when the machine is running, so only use
biodegradable oils made specifically for this use.
• To avoid the risk of fire, do not leave the machine with the
motor hot on leaves or dry grass.
m
WARNING!
It takes specific training to use this tool.
Checks During Work
• Checking the chain tension
The chain tends to stretch gradually as you work, so you need
to check its tension frequently.
dealer or call the Snow Joe
®
IMPORTANT! During the first period of use (or after replacing
the chain), the chain tension must be checked more frequently
due to settling of the chain.
m
WARNING!
Never work with the chain loose, as it can
be hazardous if the chain slips out of its guide.
To adjust the chain tension, follow the instructions in
"Adjust Chain Tension" on pages 11.
• Checking the oil delivery
IMPORTANT! Never use the machine without lubrication!
Make sure you lubricate the cutting area before and after
using, and every 30 minutes during operation. For best results,
use only a good quality bar and chain oil designed specifically
for use with chain saws. Check the oil delivery as described
below everytime after lubricate the chain.
m
WARNING!
Make sure the bar and the chain are in
place when you check the oil delivery.
Start the motor and check if the chain oil is delivered as shown
below (Fig. 9).
Fig. 9
®
Basic Cutting Procedures
m
WARNING!
This unit is designed for trimming branches
and limbs up to 4.5 in. (11.4 cm), not to exceed a max.
cut of 4.5 in. (11.4 cm) in diameter depending on type of
wood. Practice cutting a few small limbs using the following
technique to get the "feel" of using the saw before you begin a
major sawing operation.
• Grip the saw firmly on the handle grip.
• Squeeze the trigger switch and let the chain accelerate to
full speed before entering the cut.
• Keep the unit running the entire time you are cutting,
maintaining a steady speed.
• Let the chain do the work; exert only light downward
pressure. If you force the cut, damage to the bar, chain,
or unit can result.
• Do not put the pressure on the saw at the end of the cut.
• Always cut with both feet on solid ground to prevent falling.
• Do not cut above chest height since it is difficult to
control kickback forces with a saw held high.
13