Ego Power+ PH1400E Manual Del Operador página 7

ASSEMBLY
WARNING:
If any parts are damaged or missing,
do not operate this product until the parts are replaced.
Use of this product with damaged or missing parts could
result in serious personal injury.
WARNING:
Always remove the battery pack from
the product when you are assembling parts, making
adjustments, cleaning, or when the product is not in use.
INSTALLING AN ATTACHMENT TO THE POWER HEAD
WARNING:
Read and understand entire Operator's
Manual for each optional attachment used on this power
head and follow all warnings and instructions. Failure to
follow all instruc tions could result in electric shock, fire
and/or serious personal injury.
WARNING:
This 56V power head PH1400E is
designed to be used only with the EGO attachment
models that are specified in this Operator's Manual or
subsequently introduced by EGO for use with this power
head. Use of other, unauthorized attachments could cause
serious personal injuries or property damage.
WARNING:
Never install, remove, or adjust any
attachment while the power head is running or with
the battery installed. Failure to stop the motor and
remove the battery can cause serious personal injury.
NEVER OPERATE THE POWER HEAD WITHOUT AN
ATTACHMENT.
The attachment connects to the power head by means of
a coupler device.
1. Stop the motor and remove the battery pack.
2. Loosen the wing knob.
3. Remove the end cap from the attachment. Align the
arrow on the attachment shaft with the arrow on
the coupler and push the attachment shaft into the
coupler until you hear a clear "click" sound, which
indicates that the attachment shaft is mounted into
place (Fig. B).
Fig. B parts description see below:
B-1 Attachment Shaft
Arrow on the
B-2
Attachment Shaft
B-3 Wing Knob
4. Pull the shaft of the attachment to verify it is securely
locked into the coupler. If not, rotate the attachment shaft
from side to side in the coupler until it snaps into place.
5. Tighten the wing knob securely.
B-4 Arrow on the Coupler
Shaft-Release
B-5
Button
B-6 Power-head Shaft
56 VOLT MULTI TOOL POWER HEAD — PH1400E
WARNING:
Be certain the wing knob is fully
tightened before operating equipment; check it
periodically for tightness during use to avoid serious
personal injury.
REMOVING THE ATTACHMENT FROM THE POWER
HEAD
1. Stop the motor and remove the battery pack.
2. Loosen the wing knob.
3. Press the shaft-release button, with the button
depressed, pull or twist the attachment shift out of
the coupler.
MOUNTING AND ADJUSTING THE FRONT-ASSIST
HANDLE
1. Stop the motor and remove the battery pack, if installed.
2. Loosen the wing nut to separate the adjustable front-
assist handle (Fig. C).
Fig. C parts description see below:
C-1 Lock Pole C-3 Front-Assist Handle
C-2 Clamping Block C-4 Wing Nut
3. Push the front-assist handle onto the shaft between the
threshold ring and the coupler (Fig. D).
4. Insert the clamping block into the handle slot (Fig. E).
5. Mount the lock pole, and pre-tighten them with the wing
nut. Make sure that the front-assist handle is upwards
and points toward the top of the rear handle (Fig. F).
6. Adjust the front-assist handle between the threshold ring
and the coupler to make sure your front arm is straight
when operating and ensure that the arrow on the front-
assist handle is within the limitation range marked on the
coupler (Fig. G).
Fig. G parts description see below:
G-1 Arrow G-2
7. Lock the lever of the lock pole (Fig. H).
WARNING:
Never operate the tool without the front-
assist handle firmly in place.
WARNING:
Only fix the front-assist handle between
the threshold ring and the coupler.
MOUNTING THE SHOULDER STRAP
Depress the strap hook to open it and attach it onto
shoulder-strap mount hanger on the power head (Fig. I).
Limitation Range
7
EN