Descargar Imprimir esta página

RCA NaviLight8 Manual Del Usuario página 7

Publicidad

Idiomas disponibles

Idiomas disponibles

RCR860_NA_IB_REVA.qxp
3/13/06
Troubleshooting (continued)
• You may have pressed an invalid key for the mode the remote is in.
• If you're trying to turn on an RCA, GE or PROSCAN component, press the
component key instead of the ON·OFF key.
• If you're trying to change channels, try pressing the OK key after entering the
channel number as this is a requirement of certain models and brands.
• There is a possibility that a programmed code may only be able to control some
of your component features (e.g., only turns a component on and off). To confirm
that the component key is programmed with the correct code for maximum
functionality, test the component. Attempt to control a variety of the component's
functions with the remote. If some of the features of your components do not
work, try programming the remote with a different code in the list using the
Direct Code Entry Method, until you find the code that allows the remote to
control the majority of your component's functions. Different codes can provide
different levels of functionality.
Problem: The component name does not light when you press a key.
• You may have pressed an invalid key for the mode the remote is in. You must put
the remote in the correct mode by pressing the corresponding component key so
the remote knows which component you want to operate.
• Make sure the batteries are fresh and are properly installed. Replace the batteries
with two new AA batteries, if necessary. Reprogramming may be required.
Problem: The VCR won't record.
• Make sure the remote is in VCR Mode.
• Make sure the tape is properly loaded in the VCR.
• Make sure the tape is not write-protected. If the safety tab is removed, the tape is
write-protected, and you cannot record onto that tape.
Problem: The remote will not change channels on your component.
• Put the remote in the correct mode by pressing the corresponding component key
so the remote knows which component you want to operate.
• Press the OK key after you enter a channel number.
• Remove any obstacles between the remote and the component. Make sure to aim
the remote at the IR sensor on the component.
Problem: The component's menu doesn't appear on the TV screen.
• Make sure you have connected your component to your TV properly and have
selected the correct input. (See your component's Owner's Manual for proper
connection procedures.)
• Put the remote in the correct mode by pressing the corresponding component key
so the remote knows which component you want to operate.
• Menu access isn't supported for all brands. If that's the case, use your original
remote control to access menu functions for these components.
For more information, please visit www.rca.com.
Limited Lifetime Warranty
Our company (in the U.S.,THOMSON INC. / In Canada, Thomson multimedia Ltd.)
will replace this product, regardless of how long you, the original purchaser, own it
if found to be defective in materials or workmanship. For a prompt, no charge
replacement of equivalent product, return the defective product postage prepaid to
the appropriate address.
In the US:
Product Exchange Center
11721 Alameda Avenue
Socorro TX 79927
In Canada:
Thomson multimedia Ltd.
6200 Edwards Boulevard
Mississauga, Ontario Canada L5T 2V7
This replacement is the company's sole obligation under this warranty. THOMSON
INC. / Thomson multimedia Ltd. will not be responsible for any incidental or
consequential damages or for any loss arising in connection with the use or inability
to use this product. Some states/provinces do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation or exclusion may not
apply to you. This warranty excludes defects or damage due to misuse, abuse, or
neglect. This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state/province to province.
12
3:29 PM
Page 12
Contenido
Diagrama del Producto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Introducción . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Instalación e Información sobre las Pilas . . . . . . . . . . . . . . . . . . . . . . .14
Ahorro de Pila . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Ruta de Iluminación NaviLight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Nombres de los Componentes Iluminados . . . . . . . . . . . . . . . . . . . . .15
Función de Apagado Doble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Cómo Programar el Control Remoto . . . . . . . . . . . . . . . . . . . . . . . . . .15
Métodos de Programación
Búsqueda y Entrada de Códigos de Marcas . . . . . . . . . . . . . .15
Entrada Directa de Códigos . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Búsqueda y Entrada Manual de Códigos . . . . . . . . . . . . . . . .17
Búsqueda y Entrada Automática de Códigos . . . . . . . . . . . . .19
Obtención de Códigos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Cómo Utilizar el Control Remoto para Manejar sus Componentes . .21
Irrupción de Volumen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Irrupción Avanzada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Irrupción de Tecla de Transporte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Reloj de Apagado . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Resolución de Problemas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Garantía . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Teclas de componentes.
(SAT·CBL, VCR,
DVD, TV, AUX-1,
AUDIO, DVR, AUX-2)
Tecla dedicada
MENU para menús
de discos DVD,
receptores de satélite
y algunos TV.
Tecla INFO – Muestra
información relacionada
al componente que
está actualmente
manejando.
Teclas de transporte –
Teclas REVERSE,
PLAY, FORWARD,
RECORD, STOP
y PAUSE.
13
Tecla ON·OFF
(encendido·apagado)
Teclas de navegación
(teclas de flecha: hacia
arriba, hacia abajo, hacia
la derecha, hacia la
izquierda)
Teclas de CHAN Y VOL
Tecla INPUT – Cuando el
contol remoto se encuentra
en el modo TV, alterna a
través de todas las fuentes
de video conectadas a
su TV. Cuando el control
remoto se encuentra en
el modo VCR, alterna
entre la entrada VCR y TV.
Tecla SLEEP – Le
permite establecer un
lapso de tiempo en el
que su TV se apagará
automáticamente.
El modelo actual podría
ser diferente al mostrado
en la ilustración.

Publicidad

loading

Este manual también es adecuado para:

Rcr860