Asist ARZ3H001 Instrucciones De Uso página 26

3.) Helmet size
Figure L:
5.) Material
Figure M:
6.) Month of production
7.) Year of manufacture (e.g. 2017)
Corresponds to the directive for personal protective
equipment 89/686/EEC
Tested according to DIN EN 397
Hearing protection tested according to EN-352-3
Flip-up shield tested according to EN1731
Properties
Forestry helmet for working with cutting tools such as
chainsaws, hedge trimmers or delimbers
For work with cutting tools such as chain saws, hedge
trimmers or loppers
It reliably protects the head, eyes and hearing
The size of the head arch can be adjusted with a
rotary regulator (approx. 52-66 cm)
With a comfortable forehead pillow
Removable shield with adjustable distance to the face
SNR 23dB hearing protection with padded earcups -
can be flipped out during work breaks
The pressure of the shells can be adjusted for optimal
wearing comfort
Construction
● Insert the headrest 6 with all four tabs
into the helmet's internal mounts 1 until they engage
(see Fig. A).
● Insert the hearing protector holders 3 into the side
helmet attachment 1 to snap into place (see fig. C).
● Mount the visor 2 with the grid. To that end
insert the grid from the bottom into the shield so that it
snaps into place.
● Now insert the pre-assembled sight 2 into the
holder
hearing protectors 3 (see fig. D).
● Now tilt the visor 2 forward (see Fig. E).
● Now push the visor 2 into the holder as far as it
will go
hearing protectors 3 (see fig. F).
Adjusting the head holder Fig. A
● Turn the head holder setting to make the holder
heads adapted to the circumference of their heads 4.
● When putting it on, the headband is tight.
● By turning the headrest adjustment 4 in the direc-
tion
clockwise, the circumference decreases.
● By turning the headrest setting 4 in the opposite
direction
clockwise, the circumference increases.
● The helmet must fit firmly on the head, but at the
same time
must not press uncomfortably.
Hearing protector adjustment Fig. G–I
You can adjust the hearing protector to the height
and to
desired position.
● Press the ear protector holder 3 to lock it
ear protector.
● Set the desired one by moving the ear protector 3
height (see Fig. G).
● Turn the ear protector 3 to set the correct one
position (see Fig. H).
● Donning and doffing can be facilitated by
the ear protector can always be folded out individu-
ally.
If the clamping force decreases, adjust it
by adjusting the hearing protector
clamping force.
● By moving the hearing protection settings in the
direction
„+" will increase the clamping force (see Fig. I).
● By moving the hearing protection settings
in direction
„–" will reduce the clamping force (see Fig. I).
Adjustment of the visor Fig. J
By moving the sight 2 you can adjust the distance of
the sight
from the face (see Fig. J).
In addition, you can also fully tilt the visor up.
CLEANING AND MAINTENANCE
Inspect components before each use
in terms of damage and signs of wear.
● Clean the helmet after finishing work.
● Use to clean the helmet, hearing protection and
visor
damp cloth. Never use
petrol, solvents or cleaning agents which
they damage the plastic.
● Disinfect the helmet and hearing protection only
with
means that do not contain solvents
nor harsh chemicals.
● Store the helmet, hearing protection and visor in a
clean
and a dry environment protected from UV radiation.
● The helmet can be transported in its sales packa-
ging.
SPECIFICATIONS
Head circumference: 52-66 cm
total weight
(including helmet, protective shield,
2x hearing protection) approx. 700 g
Mass:
(1x hearing protection) approx. 119 g
Hearing protection material:
Holder for hearing protection: POM
Sealing cushion: PVC
Hearing protector attenuation values:
Frequency (Hz)
26
63 125 250 500