Section I
General indications
Section II
Hubs
Section III
Spokes
Section IV
Complete wheels
Section V
Fitting a tubular
Section VI
Fitting of Vibrostop
SECTION I -
General indications
We thank you for buying the SUPERTYPE 358RS Wheels, a pro-
duct that will guarantee you security and functionality through the
years.
These wheels are developed for using on roads with regular base,
SUPERTYPE 358 Wheels are hand built; ensuring that the correct
spoke tension is applied for each single spoke. The resulting built
wheel offers a level of rigidity that guarantees a secure and reliable
ride, a trade mark of Miche Hand Built wheels.
Before proceeding with using the wheels, please read carefully the
following instruction and store them in a safe place for eventually
reusing.
Fac Michelin S.p.a. reserve to modify the content of this manual
without notice. The updated version will always be available www.
michetechnology.com
On our website you will also find information on the other Miche or
Supertype products and the spare parts catalogue.
In the box of SUPERTYPE 358 Wheel set you will find:
• The font and the rear wheel
• The quick release set
• The valve extension
• Vibrostop
• Two pairs of sintered brake pads for carbon rims
• A ring for locking the cassette sprocket.
Warning!
The enclosed ring for locking the cassette sprockets is
not compatible with cassette sprockets with first posi-
tion Z=11.
• The manual of instructions and use of SUPERTYPE 358RS Whe-
els.
Attention
The pressure of the tubulars must be no higher than the
one that is indicated on the label located on the rim near
the valve hole.
Attention
Any modification or alteration (and graphic) of the pro-
duct with non-original spare parts or spare parts not de-
livered directly by Fac Michelin Spa, involves the expira-
tion of the guarantee.
Warning!
Direct and violent impacts on broken road surfaces can
cause damage to the rims. Such damage is outside the
conditions of our guarantee and repair costs will be
charged directly to the customer.
Warning!
In case of strange impact caused from bad road base or
wheels transport, we trust to bring the wheels to your
mechanic for a check.
Using only MICHE brake pads for carbon rim that you find
MAIN INDEX
inside wheel set box. Use original spare parts exclusively
provided by Fac Michelin Spa
Warning
Before using the bicycle it is necessary to:
• Check for proper operation and state of wear of all the compo-
nents before starting to ride.
• Check the condition and pressure of the tyres/tubular tyres fitted
to your wheels. Please consult the manufacture of your tyres/tubu-
lars of choice when inflating your tyres/tubulars.
• Check your wheel(s) spoke tension, to ensure there are no spo-
kes with low spoke tension. In the event of any spokes not being at
the correct tension please note that any spoke tension adjustments
must be carried out by a specialist skilled cycle mechanic.
• Check that the wheel quick release are correctly closed to en-
sure the wheels are held in the cycle frame correctly, see (Fig.7)
ATTENTION incorrect use or the loosening of the quick
release could lead to a serious or fatal accident.
• Check very carefully the alignment of the front and rear brake cal-
liper brake blocks, ensuring the break only on the correct braking
surface of the Miche wheel rim(s) also check for, and remove, any
foreign particles which may be imbedded in the break pad. [Please
note you may need to remove your Miche wheels from your cycle
to do so]
• When riding in wet conditions, remember that the stopping po-
wer of your brakes is greatly reduced and the adherence of the
tires to the ground is considerably reduced. This makes it harder
to control and stop your bicycle in wet conditions to avoid an acci-
dent. An accident could results in severe personal injury
or death.
• To the users of more than 85kg weight, Fac Michelin suggests
to check the wheels status to the mechanic every two months or
every 1,500km.
• Never wash the pieces with pressure-fed water because water
may get through the seals and cause permanent damage to the
internal components. We recommend washing components with a
sponge, mild soap, and water.
• Salt water environments (as found on winter roads and neat the
seaside) can cause galvanic corrosion on most bike parts. Carefully
rinse, clean, dry and re-lubricate all exposed parts to avoid dama-
ge, malfunctions and accidents.
SECTION II -
Warning
If you have any doubt whatsoever your service-repair
ability, please take your bicycle to a qualified repair shop.
Before any maintenance operations on your wheels,
always wear gloves and protection glasses.
Use original spare parts exclusively provided by Fac
Michelin Spa.
When replacing any broken sealed bearings please ensure sealed
bearing correct measure and specification are used.
5
Hubs
ENGLISH