Before Starting The Equipment - EINHELL TE-AP 18 Li Solo Manual De Instrucciones Original

•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Changing the saw blade (Fig. 2)
Warning!
Switch on the universal saw and pull out the bat-
tery pack each time before doing any work on the
machine and changing the blade. Turn the ring (a)
on the blade holder (4) as shown in Fig. 2 until the
blade (b) lets itself be slipped into the slot of the
blade holder (4). When you now let go of the ring
(a) again, the ring (a) should return to its starting
position. If this fails to happen, try turning the ring
(a) by hand into its starting position. Pull on the
blade to check whether it sits tightly in the holder.
5.2 Adjusting the soleplate (Fig. 3)
Warning!
Pull out the battery pack.
To adjust the soleplate, press the soleplate lo-
cking button (5) on the right-hand side (looking
from the bottom) in order to unlock the soleplate
Anl_SA_TE_AP_18_Li_SPK8.indb 34 Anl_SA_TE_AP_18_Li_SPK8.indb 34
GB
(3). Set the required distance and press the so-
leplate locking button (5) on the left-hand side
(looking from the bottom) in order to lock the sole-
plate again. Check that the soleplate is secure.
5.3 Charging the Li battery pack (Fig. 4-5)
1. Remove the battery pack (d) from the handle,
pressing the pushlock button (c) downwards to
do so.
2. Check that your mains voltage is the same
as that marked on the rating plate of the battery
charger. Insert the power plug of the charger (e)
into the mains socket outlet. The green LED will
then begin to fl ash.
3. Push the battery pack onto the battery charger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger. If the battery pack fails to charge,
check for the following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit. If the battery
pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack to our customer service
center.
5.4 Battery capacity indicator (Fig. 4 /Item f)
Press the button for the battery capacity indicator
(g). The battery capacity indicator (f) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.
- 34 -
04.10.2017 08:24:54 04.10.2017 08:24:54