Jensen CD3010X Instrucciones De Instalación

®
Welcome!
For your Jensen stereo to work right, it must be installed correctly. This manual will show you how to
install your new stereo like a pro. It's a good idea to read all of these instructions before you begin the
installation. Most installations are straightforward and can be handled by a do-it-yourselfer with the right
tools and patience. But, do-it-yourself installation isn't for everyone. You may want to turn the installation
job over to an experienced installer.
Warranty Service
If your Jensen stereo should ever require service, you will need to have the original dated receipt. If you
ever need to return the unit for any reason, always include the receipt with the product.
1. Before You Begin Installation
Tools and Supplies Needed
• Torx type, Flat and Phillips screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screw driver,
socket wrench set or other tools)
• Radio removal tool for Ford cars (early 1980s
models and newer)
• Electrical tape
• Crimping tool
• Volt meter/Test light
• Crimp connections
• 18 gauge wire for power connections
• 16-18 gauge speaker wire
2. Preparation
Radio
3 Place adhesive dots.
Press adhesive dots over
transport screw holes.
PW R
VOL
AU X
CD 301
0X
SEL MP 3/A
MUT E UX INP
COMP ACT UT
DIGITA L AUDIO
VOL
HIG H
RPT PO WE
R 45W
RPT A-B x4
1 RDM
2 INT
3 PGM
4 MEM
/CL R
5 ELA PSE
6
AS/ PS
BAS S
SCA N
DIS P
Remove Old Radio
Standard Bracket Mounted (GM, Dodge, Jeep)
Remove dashboard
1
faceplate.
Front Load Mount
Some cars use a special removal tool to release the radio (Ford and Mercury).
1 Insert removal tool(s).
Pull the radio out.
2
Replacing an Aftermarket Radio
1 Bend tabs flat.
Import Type Mount
1 Remove dash panel to
expose DIN chassis.
COMP EJE CT
ACT
DIGIT
AL AUDIO RG CD
40 0
8 X OVE
RSA
MPL ING
. . .
4 X 15
WA TTS
PW R
BA SS
MO /ST BA ND VO L
DIS P CD SE L
LO /DX
INT VO L
RP T
RD M
Install Half-sleeve
Push tabs out to
3
secure half-sleeve in
the radio opening.
Set Frequency Spacing Switch
There is a selectable frequency spacing switch on the
bottom of the unit. Before installing the unit into the
dashboard, confirm that the switch is set to the correct
setting for your area of operation.
All manuals and user guides at all-guides.com
Installation
How to Install the CD3010X AM/FM Stereo
Radio/Compact Disc Player with Remote
Control and Auxiliary Input Jack
Speaker Requirements
Only connect the CD3010X to speakers rated in
the load impedance range of 2 to 8 ohms.
Speakers with a load impedance less than 2
ohms could damage the CD3010X.
Disconnect Battery
Before you begin, always disconnect
the battery negative terminal.
Remove half-sleeve.
1
Press latches on both sides
of radio to remove half-sleeve.
Remove transport screws.
2
Remove screws before
BAN D
inserting a CD.
Unscrew brackets.
2
Disconnect wiring harness
3
and remove radio.
3 Disconnect wiring harness
and remove radio.
2 Pull sleeve from dashboard.
Remove sleeve carefully.
Caution: Edges are sharp.
Use a rag or wear a glove.
Remove screws that secure
2
radio to the dashboard.
3 Remove brackets from
the side of radio.
4 Disconnect wiring harness
and remove radio.
Install support strap
4
to make unit more
Install adapter
1
if necessary.
(optional)
Install half-sleeve into
2
adapter or dashboard.
Europe
3. Wiring
Wiring with a Wiring Adapter (Purchase Separately)
Connect Wires
Splice or crimp
1
Refer to Wiring
Diagram for correct
wire color codes.
Wiring Diagram
LF LF–
white/black
white
LF+
LR–
green/black
green
LR+
LR
Reconnect Battery
When wiring is complete, reconnect
the battery negative terminal.
4. Final Installation
Replace any items
5
you removed
from the dashboard.
PW R
VOL
AUX
CD3 010
SEL X
MP3 /AU
MUT E X INP
COMPA
CT
DIGITA
VOL L AUDIO
RPT
RPT A-B
1 RDM
2 INT
3 PGM
4
5
Final Installation–ISO-DIN
Slide radio chassis into dash
2
opening and secure.
5. Troubleshooting
Problem
Does not operate (display
does not light)
No power to unit
No speakers operate
stable.
(display lights normally)
Not all speakers operate
Blows fuses
ER-2 appears on display
ER-3 appears on display
ER-4, ER-7, ER-8
appears on display
ER-5, ER-6 appears on display
CD skips too much
USA
Technical Assistance
M – F 8:00 am to 6:00 pm EST @1.800.323.0221 • 365 / 24 / 7 @ www.jensenaudio.com
Jensen Connector
You can make all these connections
without even being in the car.
Attach wiring adapter
2
to car wiring harness.
10A
RCA-to-RCA cables
(See amplifier instructions)
(not supplied)
Red
White
Power Antenna
Connect to power antenna or amplifier. If not used,
tape bare end of wire.
Dark Blue
AMP
Ground
Connect to ground terminal or clean, unpainted part
Black
of chassis.
Memory/Battery
+ –
Connect to battery or 12 volt power source that is
Yellow
always alive.
The radio will not work if this wire is not
connected.
Accessory/Ignition
Red
Connect to existing radio wire or radio fuse.
RF– RF
gray/black
Fuses
gray
When replacing a fuse, make sure new fuse is correct
RF+
type and amperage. Using an incorrect fuse could
RR–
damage radio. The CD3010X uses one 10 amp fuse
violet/black
located below wiring connector.
violet
• 10 amp fast blow ATO
RR+
RR
Secure Radio to
4
bracket using nut.
(if possible)
UT
HIG H
POW
ER 45W
x4
MEM
/CLR 2
ELA PSE
6
BAN D
AS/P
S
BAS S
SCA N
DISP
Slide radio chassis
3
into half-sleeve.
PWR
VOL
AUX
CD3 010X
SEL MP3 /AUX
MUTE INPU T
COMPAC T
DIGITAL
VOL AUDIO
HIGH
RPT POW ER 45W
RPT A-B
x4
1 RDM
2 INT
3 PGM
4 MEM
/CLR
5 ELAP SE
6
AS/P BAN D
S
BAS S
SCA N
DISP
Reinstall dash panel.
3
Cause
No power to yellow wire
No power to red wire
Inline fuse blown
Inline fuse blown
Speaker harness not connected
Incorrect splices or connections
Speaker wires shorting to chassis
ground or to each other
Power wire shorting to ground
Speaker wires shorting to ground
Incorrect fuse/fuse too small
Disc loading malfunction
Disc eject malfunction
Disc reading malfunction
Track change malfunction
Receiver mount is not solid or
backstrap is not secure
Amplifier wiring
AMP
Connect wiring adapter
1
to existing wiring harness.
Connect antenna lead.
1 Mount factory brackets on
new radio using existing
screws from old radio.
Corrective Action
Check connection with test light.
Check vehicle fuse with test light.
Replace fuse.
Check/replace fuse.
Connect speaker harness.
Check speaker wires.
Check all splices and connections.
Check splices, insulate all bare wires.
Make sure wire is not pinched.
Make sure wire is not pinched.
Install fuse of correct rating.
Press RESET button. Insert disc and try again.
Press RESET button. Insert disc and try again.
Try a different disc. The disc may be
damaged or dirty.
Press RESET button. Insert disc and try again.
Check mounting and backstrap, tighten if
needed.