Bosch GWS Professional 20-180 Manual Original página 18

18 | English
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Release the On/Off switch and set it to the off position
u
when the power supply is interrupted, e. g., in case of
a power failure or when the mains plug is pulled. This
prevents uncontrolled restarting.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for cutting, roughing and brush-
ing metal and stone materials without the use of water.
A separate protective guard for cutting must be used when
cutting with bonded abrasives.
Technical data
Angle grinder
Article number
Rated power input
Power output
Rated speed
Max. grinding disc diameter
Grinding spindle thread
Max. thread length of grinding spindle
Weight according to EPTA-Procedure 01:2014
– with low-vibration auxiliary handle
– with standard auxiliary handle
1 609 92A 431 | (08.04.2021)
Sufficient dust extraction must be provided when cutting
stone.
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Spindle lock button
(2) On/off switch
(3) Side handle (insulated gripping surface)
(4) Grinding spindle
(5) Protective guard for grinding
(6) Locking screw for protective guard
(7) Hub flange with O‑ring
(8) Grinding disc
(9) Clamping nut
(10) Two-pin spanner for clamping nut
(11) Quick-clamping nut
(12) Carbide grinding head
(13) Protective guard for cutting
(14) Cutting disc
(15) Hand guard
(16) Spacer discs
(17) Rubber sanding pad
(18) Abrasive disc
(19) Round nut
(20) Cup brush
(21) Extraction guard for cutting with a guide block
(22) Diamond cutting disc
(23) Handle (insulated gripping surface)
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
GWS 20-180 H GWS 20-230 H GWS 21-180 H GWS 21-230 H
3 601 H49 L.. 3 601 H50 L..
W 2000
W 1250
-1
min 8500
mm 180
M 14
mm 25
kg 5.1
kg 5.0
a)
a)
a)
a)
a)
a)
a)
a)
a)
a)
a)
a)
a)
3 601 H51 L.. 3 601 H52 L..
2000 2100
1250 1350
6600 8500
230 180
M 14 M 14
25 25
5.4 5.1
5.3 5.0
Bosch Power Tools
a)
2100
1350
6600
230
M 14
25
5.4
5.3