Oxygenated Fuels - RIDGID RD80704 Manual Del Operador

OPERATION
 Insert a clean funnel into the fuel tank then slowly
pour gasoline into the tank. Fill tank to approximately
1/2 in. below the top of the tank neck (this allows for fuel
expansion).
 Replace fuel cap and tighten securely.
 Clean up any spills before starting the engine.

OXYGENATED FUELS

DO NOT USE E85 FUEL. IT WILL VOID YOUR WARRANTY.
NOTE: Fuel system damage or performance problems re-
sulting from the use of an oxygenated fuel containing more
than the percentages of oxygenates stated below are not
covered under warranty.
Ethanol. Gasoline containing up to 10% ethanol by volume
(commonly referred to as E10) is acceptable. E85 is not.
STARTING AND STOPPING THE PRESSURE
WASHER
See Figures 14 - 16.
CAUTION:
Do not run the pressure washer pump without water
supply connected and turned on, as this may dam-
age the high pressure seals and decrease pump
life. Completely unwind the hose from its reel or coil
and make sure the hose is not being restricted by
tires, rocks, or any other objects that may lessen or
prevent water flow to the pressure washer.
Before starting the engine, connect all hoses and check all
fluids (oil and gas). Turn the garden hose on then squeeze
the trigger. This relieves air pressure caused by turning on the
water. Hold the trigger until a steady stream of water appears.
To start an engine that is cold or has run dry:
 Close the fuel valve.
 Fill the fuel tank (if necessary).
 Connect the garden hose to the pump and turn on the
water supply.
 Open the fuel valve.
 Place the engine switch in the ON ( l ) position.
 Push the choke lever to the closed position.
NOTE: If the engine is cold, close the choke fully. If the
engine is warm, open the choke lever half-way or keep it
opened fully.
 Give the recoil starter short, brisk pulls to start the
engine.
 If the engine fires, or begins to sputter and/or cough
without catching, move the choke lever to the half-way
position.
NOTE: Never pull the recoil starter more than four or five
times with the choke closed as this causes flooding.
CAUTION:
If the engine does not start after each pull of the
starter grip and rope, squeeze the trigger to relieve
water pressure before attempting to start the engine
again.
 With the choke in the half-way position, pull the recoil
starter again. The engine should now start.
NOTE: If the choke remains in the closed position, the
engine will continue to sputter and/or cough but will not
start.
 Return the recoil starter gently to the engine housing. Do
not allow the rope to snap back.
 As the engine warms up, move the choke lever slowly to
the opened position.
 Let the engine warm up a few minutes before using.
To stop the engine using the engine switch:
 Turn the engine switch to off ( O ) position.
 Close the fuel valve.
USING THE SPRAY WAND TRIGGER
See Figure 17.
For greater control and safety, keep both hands on the
trigger handle at all times.
 Pull back and hold the trigger to operate the pressure
washer.
 Release the trigger to stop the flow of water through the
nozzle.
To engage the lock out:
 Pull up on the lock out until it clicks into the slot.
To disengage the lock out:
 Push the lock out down and into its original position.
For the most effective cleaning, the spray nozzle should be
between 8 in. and 24 in. from the surface to be cleaned. If
the spray is too close it can damage the cleaning surface.
USING THE NOZZLES
See Figure 17 - 18.
Each of the nozzles has a different spray pattern. Before
starting any cleaning job, determine the best nozzle for the
job. The following chart offers some general guidelines to
help you choose the best nozzle for your application.
Nozzle
0º Red Spot cleaning of high, hard-to-reach areas
• Removing caked-on mud from heavy con-
struction, farm, or lawn equipment
• Cleaning tar, glue, or stubborn stains from
concrete
• Cleaning overhead areas
• Removing rust from steel and oxidation
from aluminum
10 - English
Application