Publicidad
Idiomas disponibles
Idiomas disponibles
MAINTENANCE & REPAIR INSTRUCTIONS
dirty spark plug. Set the air gap at 0.025 in. (0.635 mm) using a feeler
gauge (Fig. 28).
5.
Install a correctly-gapped spark plug in the cylinder head. Turn the 5/8
in. socket clockwise until snug.
If using a torque wrench torque to: 110-120 in.•lb. (12.3-13.5 N•m)
Do not over-tighten.
SPARK ARRESTOR
MAINTENANCE
1.
Remove the rear engine
cover. See Rocker Arm
Clearance.
2.
With a flat blade screwdriver
or Torx T-20 bit and a T-25
bit, remove the screws
attaching the spark arrestor
cover to the muffler (Fig. 29).
3.
Pull the tab on the spark
arrestor cover out of the
muffler. Remove the spark arrestor cover.
4.
Remove the spark arrestor screen from the spark arrestor cover.
5.
Clean the spark arrestor screen with a wire brush or replace it.
WARNING:
To avoid serious personal injury, always turn the
unit off and allow it to cool before cleaning or maintaining it.
6.
Reinstall the spark arrestor screen, spark arrestor cover and screws.
CLEANING
Use a small brush to clean off the outside of the unit. Do not use strong
detergents. Household cleaners that contain aromatic oils such as pine and
lemon, and solvents such as kerosene, can damage plastic housing or handle.
Wipe off any moisture with a soft cloth.
STORAGE
• Never store the unit with fuel in the tank where fumes may reach an open
flame or spark.
• Allow the engine to cool before storing.
• Lock up the unit to prevent unauthorized use or damage.
• Store the unit in a dry, well-ventilated area.
• Store the unit out of the reach of children.
LONG TERM STORAGE
1.
Drain all gasoline from the gas tank into a container. Do not use gas
that has been stored for more than 60 days. Dispose of the old gasoline
in accordance to Federal, State, and Local regulations.
2.
Start the engine and allow it to run until it stalls. This ensures that all
gasoline has been drained from the carburetor.
3.
Allow the engine to cool. Remove the spark plug and put 5 drops of
high quality motor oil into the cylinder. Pull the starter rope slowly to
distribute the oil. Reinstall the spark plug.
NOTE:
Remove the spark plug and drain all of the oil from the cylinder
before attempting to start the unit after storage.
4.
Change the oil, referring to Changing the Oil. Dispose of the old oil in
accordance to Federal, State and Local regulations.
5.
Thoroughly clean the unit and inspect for any loose or damaged parts.
Repair or replace damaged parts and tighten loose screws, nuts or
bolts. The unit is ready for storage.
TRANSPORTING
• Allow the engine to cool before transporting.
• Secure the unit while transporting.
• Drain the gas tank before transporting.
• Tighten gas cap before transporting.
Spark Arrestor
Muffler
Screen
Cover
Slot
T-20 Screw
Fig. 29
PLUG-IN POWER START AND POWER BIT START FEATURES
This unit is designed to be started with an optional Plug-In Power Start or
Power Bit Start that are sold separately. If choosing to start the unit using
one of these features or have questions please contact your local retailer or
call 1-800-4-MY-HOME®, for more information and purchasing. You may
also go to www.craftsman.com.
T-25
Screw
Item No.
316.85951 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Plug-In Power Start
316.85952 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Power Bit Start
9
OPTIONAL ACCESSORY
Electric Start Feature
Description
Publicidad
