Kenmore 139.20153510 Manual De Uso Y Cuidado página 9

Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
•Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution
or specially formulated cleaner. Use nonabrasive scouring
powder for stubborn stains.
•Painted surfaces: Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
nonabrasive cloth.
•Stainless steel surfaces: To maintain your grill's high quality
appearance, wash with mild detergent and warm soapy
water and wipe dry with a soft cloth after each use. Baked-
on grease deposits may require the use of an abrasive plastic
cleaning pad. Use only in direction of brushed finish to avoid
damage. Do not use abrasive pad on areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean any of
the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.
•Grease Tray and Cup: Regularly clean the grease drippings from
the Grease Tray and Grease Cup. When the grill has completely
cooled down after use, remove the cup from the tray and slide
the tray out of the grill. Clean the grease drippings from the cup
and tray surfaces by washing with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
nonabrasive cloth. Slide the tray back into the grill and replace
the cup back into the tray before using the grill again.
SPIDER ALERT!
SPIDER AND WEBS
INSIDE BURNER TUBE
If you notice that your grill is getting hard to light or that
The flame isn't as strong as it should be, take the time to
check and clean the burner tubes.
Spiders or small insects have been known to create
"flashback" problems. The spiders spin webs, build nests
and lay eggs in the grill's burner tubes obstructing the
flow of gas to the burner. The backed-up gas can ignite
in the burner tube behind the control panel. This is known
as a flashback and it can damage your grill and even
cause injury.
To prevent flashbacks and ensure good performance the
burner and burner tube assembly should be removed
from the grill and cleaned before use whenever the grill
has been idle for an extended period.
Drawer Removal and Replacement
Remove the two center drawers to clean grill interior surfaces as
described in the procedure below.
CAUTION: Be extremely careful of hand and finger placement
when removing or replacing drawers. Drawer and slider edges
can cut exposed skin. Wear protective gloves when removing or
replacing drawers.
1. Pull the top drawer out as far as it will go until it comes to a
stop.
2. On the drawer sliders, press the right release lever down and
the left release lever up at the same time. See Figure below.
3. CAREFULLY slide the drawer back about an inch. Now grasp
the drawer by the handle with both hands and pull it all the way
out of the grill.
4. Repeat the three previous steps for the bottom drawer.
5. To replace each drawer, insert the ends of the drawer sliders
into the ends of the drawer brackets on the grill. Push drawer in
all the way until it closes.
Storing Your Grill
•Clean cooking grates.
•Store in dry location.
•When LP cylinder is connected to grill, store outdoors in a
wellventilated space and out of reach of children.
•Cover grill if stored outdoors. Choose from a variety of grill
covers offered by manufacturer.
•Store grill indoors ONLY if LP cylinder is turned off and
disconnected, removed from grill and stored outdoors.
•When removing grill from storage, follow "Cleaning the Burner
Assembly" instructions before starting grill.
Cleaning the Burner Assembly
Follow these instructions to clean and/or replace parts of
burner assembly or if you have trouble igniting grill.
1. Turn gas off at control knobs and LP cylinder.
2. Remove cooking grates and heat diffusers.
3. Remove cotter pins from rear of burners.
4. Carefully lift each burner up and away from valve openings.
9
cotter pin