KRESS KG633E Manual De Instrucciones página 13

VIBRATION INFORMATION
Typical weighted vibration
The declared vibration total value may be used for
comparing one tool with another, and may also be
used in a preliminary assessment of exposure.
WARNING: The vibration emission value during
actual use of the power tool can differ from the
declared value depending on the ways in which the
tool is used dependant on the following examples
and other variations on how the tool is used:
How the tool is used and the materials being cut or
drilled.
The tool being in good condition and well
maintained.
Using the correct accessory for the tool and ensuring
it is sharp and in good condition.
The tightness of the grip on the handles and if any
anti vibration accessories are used.
And the tool is being used as intended by its design
and these instructions.
This tool may cause hand-arm vibration
syndrome if its use is not adequately managed.
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the operating
cycle such as the times when the tool is switched off and
when it is running idle but not actually doing the job. This
may significantly reduce the exposure level over the total
working period.Helping to minimise your vibration
exposure risk.Maintain this tool in accordance with
these instructions and keep well lubricated (where
appropriate).If the tool is to be used regularly then
invest in anti vibration accessories.
Plan your work schedule to spread any high vibration
tool use across a number of days.
ASSEMBLY & OPERATION
NOTE: Before using the tool, read the
instruction book carefully.
BEFORE OPERATION
Installing the battery pack (See Fig. A1)
Removing the battery pack (See Fig.A2)
Checking the battery condition(See Fig.A3)
NOTE: Fig. A3 only applies for the battery pack with
battery indicator light.
Charging the battery pack(See Fig. A4)
More details can be found in charger's manual
a = 0.841m/s
2
h
K= 1.5m/s
2
ASSEMBLY
Working mode 1 (See Fig. B1)
Attaching pressure cleaning lance to the power
nozzle.
NOTE: The power nozzle has three working modes:
pressure cleaning lance only, short lance only and
short lance used together with extension lance.
Working mode 2 (See Fig. B2)
Attaching short lance to the power nozzle
Working mode 3 (See Fig. B3, B4)
Attaching extension lance to the power nozzle
Attaching short lance to the extension lance
Attaching the Multi-spray nozzle
(See Fig. C)
NOTE: When attaching, rotate the nozzle left and
right to make sure the nozzle is fully seated into
position and gently pull it to make sure it is locked
into position securely.
Attaching the hose to the power nozzle
(See Fig. D1, D2 , D3)
NOTE: After the hose is attached, check the
connection by gently pulling upon the hose. It should
not be pulled off.
OPERATION
WARNING: The supplied battery is not
waterproof. To avoid risk of battery failure,
protect the battery from water exposure during
use. Store the tool and battery in a dry place after
use.
Start(See Fig. E1,E2,E3)
NOTE: At the first use or after long-term storage, it is
recommended to attach the tap or inject water into
the hose adapter with the machine turned on, so as
to empty the air. Do not start working until the water
goes up along the hose and sprays out.
Selecting the nozzle pattern (See Fig.F)
NOTE: Choose a suitable nozzle pattern according
to your work. Spray patterns 0
applicable for cleaning, and the spray
pattern with the symbol
watering.
WARNING: Do not shift the nozzle pattern
when the tool is powered on.
Cleaning(See Fig.G,H)
WARNING: Do not connect the machine to water
supplies that are dirty, rusty, muddy, or corrosive.
(Including window cleaning liquids, plant foods, or
fertilizers etc.)
NOTE: If sea water is used, the product should be
rinsed and used with fresh water after that in order to
, 15 , 25 and 40 are
o o o o
is best suitable for
13
EN