BTI PROFILINE A-BS 12V Manual Original página 26

Intended Use
The machine is intended for driving in and loosening
screws as well as for drilling in wood, metal, ceramic
and plastic.
Product Features
The numbering of the product features refers to the
illustration of the machine on the graphics page.
1 Keyless chuck
2 Torque preselection ring
3 Gear selector
4 Screwdriver bit*
5 Battery unlocking button
6 Battery*
7 Rotational direction switch
8 On/Off switch
9 Universal bit holder*
10 Securing screw for keyless chuck
11 Allen Key**
*Accessories shown or described are not part of the
standard delivery scope of the product. A complete
overview of accessories can be found in our acces-
sories program.
**Commercially available (not included in the delivery
scope)
Technical Data
Cordless Drill/Driver
Article number
Rated voltage
No-load speed
– 1st gear
– 2nd gear
Max. torque for hard/soft
screwdriving application
according to ISO 5393
Max. drilling dia.
– Steel
– Wood
Max. screw dia.
Chuck clamping range
Drill spindle thread
Weight according to
EPTA-Procedure
01/2003
Technical data determined with 2.0 Ah NiCd battery.
Please observe the article number on the type plate of your
machine. The trade names of the individual machines may
vary.
26 | English
A-BS 12V
9023898
V= 12
-1
min 0 – 400
-1
min 0 – 1400
Nm 34/20
mm 10
mm 25
mm 7
mm 1.5 – 10
½"
kg 1.8
Noise/Vibration Information
Measured values
EN 60745.
Typically the A-weighted sound pressure level of the
product is less than 70 dB(A). Uncertainty K = 3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values (triax vector sum) determined
according to EN 60745:
Drilling into metal:
2
a <2.5 m/s , Uncertainty K =1 m/s
h
Screwdriving: Vibration emission value a
2
Uncertainty K =1 m/s
The vibration emission level given in this information
sheet has been measured in accordance with a stand-
ardised test given in EN 60745 and may be used to
compare one tool with another. It may be used for a
preliminary assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is
used for different applications, with different accesso-
ries or poorly maintained, the vibration emission may
differ. This may significantly increase the exposure
level over the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the expo-
sure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as: main-
tain the tool and the accessories, keep the hands
warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that the
product described under "Technical Data" is in con-
formity with the following standards or standardization
documents: EN 60745 according to the provisions of
the directives 2004/108/EC,
28 Dec 2009), 2006/42/EC (from 29 Dec 2009).
Technical file at:
BTI Befestigungstechnik GmbH
D-74653 Ingelfingen
Jürgen Dietz
General Manager
28.10.2008, BTI Befestigungstechnik GmbH
74653 Ingelfingen
determined according
Vibration emission
2
,
<2.5 m/s
h
.
98/37/EC
i. V. Günter Hub
Purchasing Manager
1 609 929 S52 • 16.1.09
to
value
2
,
(until