Bpt HAV/200 US Instrucciones De Instalación

NOTE: This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a par-
ticular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
170 mm
500 mm
h
02.2009/2405-8101
All manuals and user guides at all-guides.com
710 mm 170 mm
140 mm
530 mm
140 mm
500 mm
HAV/200 US
HA/200 US
INSTALLATION
EN
INSTRUCTIONS
AUDIO-VIDEO MODULE HAV/200
The module comes complete with
- CCD camera which can be rotated
manually both horizontally and vertical-
ly by ± 11° (fig. 1), with fixed-focus lens
(see fig. 2 for the dimensions of the
field of view);
- phonic group (the microphone can be
removed and fitted in a remote position
where the installation features so requi-
re);
- infrared LED for lighting the caller;
- two potentiometers for the following
functions (fig. 3):
entry panel volume control
receiver volume control
Function of each terminal (fig. 3)
1 5 – 14 17.5 VDC
6 + supply voltage
11 audio to receiver
12 audio from receiver
14 enabling
V– negative video signal
V+ positive video signal
V+ video signal
VS video signal shield
( 1 ) Terminals for use when the video
signal is transmitted via twisted
pair.
( 2 ) Terminals for use when the video
signal is transmitted via coaxial
cable.
Functions of the SW1 jumper (fig. 3)
SW1 in position C: transmission of the
video signal via coaxial cable.
SW1 in position T: transmission of the
video signal via twisted pair.
Technical features
• Video signal system: EIA (CCIR).
• Sensor: 1/4" CCD.
• Horizontal frequency: 15,750 Hz EIA
(15,625 Hz).
• Vertical frequency: 60 Hz EIA (50
Hz).
• Video output: 1 Vpp composite to 75
Ω.
• Resolution: 380 lines.
• Minimum illumination: 5 lux.
• S/N ratio: 45 dB.
• Iris control: automatic electronic in
the range 1/50 s 1/100,000 s.
• Lens: fixed-focus f 3.7 F 4.5.
• Supply voltage: 14÷17.5 VDC.
• Current demand: 250 mA.
• Working temperature range: from -
2
15 °C to +50 °C.
BPT S.p.A.
Via Cornia, 1
33079 Sesto al Reghena-PN-Italy
info@bpt.it – www.bpt.it
AUDIO MODULE HA/200
The unit comes complete with:
- loudspeaker;
- microphone which can be removed
and fitted in a remote position where
the installation features so require;
- two potentiometers for the following
functions (fig. 4):
entry panel volume control
receiver volume control
Function of each terminal (fig. 4)
5 –
12 V DC supply voltage
21 +
8 common call (for witness note)
11 audio to receiver
12 audio from receiver
14 enabling
NOTE. In installations which do not
cater for the enabling control, termi-
nal 14 can be connected to the earth
(module always on) or terminal 12
(module on only when receiver is lif-
ted).
Technical features
• Supply voltage: 12 VDC.
( 1 )
• Current demand: max. 50 mA (35
mA quiescent).
( 2 )
• Working temperature range: from -
15 °C to +50 °C.
DISPOSAL
Do not litter the environment with
packing material: make sure it is dis-
posed of according to the regulations
in force in the country where the prod-
uct is used.
When the equipment reaches the end
of its life cycle, take measures to
ensure it is not discarded in the envi-
ronment.
The equipment must be disposed of in
compliance with the regulations in
force, recycling its component parts
wherever possible.
Components that qualify as recyclable
waste feature the relevant symbol and
the material's abbreviation.
1