Urmet 1051/020 Manual De Instrucciones página 4

POWER SUPPLY
The Urmet ZENO control unit is powered by the 230Vac electrical network.
Power supply: 100-240Vac 50/60Hz
Maximum consumption: 400mA @ 230VAC
Connect the supplied cable to the two terminals on the side of the control
unit.
After connecting the cable to the mains and powering up the control unit,
move the battery switch to ON.
As soon as the control panel is powered, the first line of the display shows the
system status (OFF by default), while the second line shows the information
relating to the date and time:
R e a d y
1 3 : 0 0
After entering the Installer code, move around the display with the arrow keys
 until the menu highlighted on the right is displayed. Select Device +/-
and press OK. Select Add Device and press OK.
The control panel enters the learning phase and a 2-minute time out will be
activated to carry out the learning of the device (at the end of the time, the
control panel will automatically exit learning mode).
Press the learn button on the device (see individual device manuals for more
details).
 P u s h
D e v i c e
The control panel can be programmed also using a PC via the included
Ethernet cable (reference manual Installation and programming via PC). There
are two types of connection:
- via the ADSL router to connect the control panel to the Internet
(recommended method)
- via direct connection to the PC
To identify and locate the control panel in the local network (LAN), Urmet
provides the Finder software, running on Microsoft Windows 7 or higher
operating system. The
https://www.urmet.com, in the 1051/020 product section.
Hereby, URMET S.p.A. declares that the radio equipment type IP 4G WIFI WIRELESS CONTROL PANEL 1051/020 are in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.urmet.com.
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012 on waste electrical and electronic equipment (WEEE).
The symbol of the crossed-out wheeled bin on the product or on its packaging indicates that this product must not be disposed of with your other
household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling
of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you
can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you
purchased the product.
DS1051-309
URMET S.p.A.
10154 TORINO (ITALY)
VIA BOLOGNA 188/C
Tel. +39 011.24.00.000 (RIC.AUT.)
BASIC PROGRAMMING BY KEYBOARD
t o a r m
N o v 3 0
DEVICES LEARNING PROCEDURE BY KEYBOARD
b u t t o n O n 
t o A d d
PROGRAMMING OVER THE WEB PAGE
software is available on
SIMPLIFIED EU DECLARATION OF CONFORMITY
FIRST START
LANGUAGE SELECTION
When the control panel is powered, two short beeps are emitted. Keep
pressed the 
code 1234 and press OK. The display shows "Codice Install", digit the Installer
code 7982 and press OK. Move with the arrows until you see the menu
"Impost. Sistema", press OK. Move to the "Lingua" menu and press OK.
Choose English.
The display will show menus in English.
Step 1. Press and hold down the  key on the keyboard for 3 seconds. The
display will ask for the User PIN Code to be entered (default 1234).
Step 2. Press the OK key. The display will ask for the Installer Code to be
entered (default 7982).
If the control unit receives the learning code, it emits 2 short 'beeps' and
displays the type of device and successful reception. Press OK to confirm
learning (example below).
ACCESSING TO THE CONTROL PANEL
Launch the Finder software and select the control panel. Click on Open
Webpage to connect to the control panel.
Alternatively, use a browser by typing in the IP address of the control panel
displayed by the Finder software in the address bar.
In the login request window, enter the default username and password
shown below and press OK.
Username: admin
the website
Password: cX+HsA*7F1
button. The display shows "Inserire Codice", digit the User
E n t e r C o d e
. . . .
E n t e r I - C o d e
. . . .
D e v i c e + / -
C o n n . S t a t u s
A d d D e v i c e
E d i t D e v i c e
D C
I n s t a l l e d ( O K ? )
Technical Assistance – Customer Care
+39 0112339810
www.urmet.com
Made in Taiwan to Urmet specification
- info@urmet.com