Descargar Imprimir esta página

HIKOKI CG 24EBS S Instrucciones De Manejo página 9

Publicidad

Idiomas disponibles

Idiomas disponibles

CAUTION
Do not disassemble the recoil starter. You may get a possibility
of personal injury with recoil spring.
SPECIFICATIONS
Engine
Displacement (cm
)
3
Spark plug
Idling speed (min
)
-1
Speed of output shaft (min
Max. engine output (kW)
Fuel tank capacity (cm
)
3
Dry weight (kg)
Cutting attachment
Sound pressure
level LpA
(dB (A))
Measured sound
power level LwA (dB (A))
Guaranteed sound
power level LwA (dB (A))
Vibration level (m/s
) (ISO22867)
2
Equivalent (Front / Left handle)*
Equivalent (Rear / Right handle)*
Uncertainty
NOTE
Equivalent noise level/vibration level are calculated as the time-weighted energy total for noise/vibration levels under various working
conditions with the following time distribution:
* 1/2 Idle, 1/2 racing.
All data subject to change without notice.
ASSEMBLY PROCEDURES
Drive shaft to engine (Fig. 1)
Loosen tube locking bolt (1) about ten turns so that the bolt point will
not obstruct drive shaft tube to be inserted. When inserting drive
shaft tube, hold the tube locking bolt outward preventing inside
fi tting from obstructing as well.
Insert the drive shaft into the clutch case of the engine properly until
the marked position (2) on the drive shaft tube meets the clutch
case.
Some models may come with the drive shaft already installed.
NOTE
When it is hard to insert drive shaft up to the marked position on
the drive shaft tube, turn drive shaft by the cutter mounting end
clockwise or counter-clockwise. Tighten tube locking bolt lining
up the hole in the shaft tube. Then tighten clamp bolt securely.
Model
(SL)
23.9
CHAMPION CJ6
2800 - 3200
)
7600
-1
Type
Nylon cord
(ISO22868)
Equivalent*
Uncertainty
(2000/14/EC)
Racing
(2000/14/EC)
Racing
CG24EBS
(S)
23.9
CHAMPION CJ6
2800 - 3200
7600
0.8
0.8
4.9
5.1
Nylon cord
85
85
3
3
108
108
111
111
5.6
3.9
4.0
2.7
2.0
1.2
Installation of handle (Fig. 2-4)
Attach the handle to the drive shaft tube with the angle towards the
engine.
Adjust the location to the most comfortable position before
operation.
NOTE
If your unit has handle location label on drive shaft tube, follow
the illustration.
Remove the handle bracket (3) from the assembly. (Fig. 3)
Place the handles and attach the handle bracket with four bolts
lightly. Adjust to appropriate position. Then attach it fi rmly with the
bolts.
Attach the protection tube to the drive shaft or handle using cord
clamps (4). (Fig. 4)
Throttle wire / stop cord
Press the upper tab (5) and open the air cleaner cover. (Fig. 5)
Connect stop cords. (Fig. 6)
CG27EBS
(SL)
26.9
CHAMPION CJ6
CHAMPION CJ6
2800 - 3200
2800 - 3200
7600
0.9
520
5.1
Nylon cord
86
3
108
111
6.7
4.1
2.0
English
(S)
26.9
7600
0.9
5.3
Nylon cord
86
3
108
111
4.1
3.0
1.2
9

Publicidad

loading

Este manual también es adecuado para:

Cg 27ebs sCg 24ebs slCg 27ebs sl