Manuales relacionados para Truper MOG-65
Resumen de contenidos para Truper MOG-65
- Página 1 Manual Gasoline 6.5 Hp / 9 Hp / 13 Hp Engine Power Applies for: Codes Models 101327 MOG-65 101328 MOG-90 101329 MOG-130 Read this manual thoroughly CAUTION before using the tool.
- Página 2 Keep this manual for future references. Fuel and Oil The illustrations in this manual are for reference Start Up only. They might be different from the real tool. Maintenance Troubleshooting Notes Authorized Service Centers Warranty Policy MOG-65 MOG-90 MOG-130 ENGLISH...
- Página 3 Technical Data MOG-65 MOG-90 MOG-130 Code 101327 101328 101329 Description Gasoline Engine Motor Cylinders 212 cm 270 cm 420 cm Motor Rated Power 6.5 Hp 9 Hp 13 Hp Max. Torque 16.4 Nm 13.5 Nm 26.5 Nm Motor Type 4-stroke OHV Diameter / Type shaft 3/4”...
- Página 4 General Safety Warnings for Motor Tools Keep your work area clean, tidy and well lit. Wear adequate protective safety accessories. CAUTION CAUTION Cluttered and dark areas may cause accidents. Wear eye protection, dust mask, non-skid safety shoes, helmet and ear plugs. These safety gears reduce the risk Never use the tool in explosive areas or in the presence of injury.
- Página 5 Safety Warnings for Gasoline Engines Fuel Handling • Never smoke close to where there is fuel, nor the filling up zone or when operating the pump. • To reduce risk of fire or burns, handle fuel with care. It is extremely flammable. •...
- Página 6 Parts Fuel Tank Cap Exhaust Fuel tank Filter Spark Plug Oil Supply Shaft Oil Drain Cap Throttle Choke Start Lever Knob Fuel Key Starter jack-line Supply Oil Drain Cap ENGLISH...
- Página 7 Assembly Engine mount • The motor must be attached to a plate (A) welded to the structure or chassis of the machine where the engine will be housed. This plate must be larger than the base of the engine and have four perforations to fix the motor with four sets of hexagonal bolts.
- Página 8 Fuel and Oil Oil Supply (A) Fuel Supply (B) • Set the equipment onto a flat and leveled surface. • Set the Pressure Washer on a flat and leveled surface. • Turn and remove the oil supply cap. • Clean and dry the area around the fuel cap. •...
- Página 9 Start Up Start Up CAUTION Before starting the pump some topics need to be taken care of. Otherwise it can get damaged and the Warranty cancelled: • All the hoses shall be disconnected, totally untangled and with no kinks. • Water supply shall be connected and fully open. •...
- Página 10 Maintenance CAUTION • Regular and careful maintenance is • Any worn or damaged part shall be replaced before essential to maintain the safety levels and the optimal using the equipment. Do not try to repair the parts. It can performance of the equipment. damage the equipment and become a risk to your safety.
- Página 11 Maintenance Fuel Filter Spark Plug • The fuel filter stops water or dirt present in the fuel • Before removing the spark plug (B), wipe clean the area tank to enter into the carburetor. around the spark plug base to stop dust and debris If the motor has not been run after a long period of time, entering the motor.
- Página 12 Troubleshooting Problem Cause Solution Motor does not start. • The switch is OFF. • Turn ON the switch. • Not enough fuel. • Fill up fuel tank. • Oil level is too low or there is no oil. • Check oil level as indicated in page 8. •...
- Página 13 Notes ENGLISH...
- Página 14 Notes ENGLISH...
- Página 15 In the event of any problem contacting a Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 0187-8737 to get information about the nearest Service Center. DE TODO PARA LA CONSTRUCCIÓN FIX FERRETERÍAS...
- Página 16 . Transportation costs resulting from compliance of this warranty will be covered by For questions or comments, call 800-690-6990. Made in China. Imported by Truper S.A. de C.V. Parque Industrial 1, Jilotepec, Edo. de Méx. C.P. 54240 Stamp of the business.