System Sensor M201EA-HC Instrucciones De Instalación

Fig./Abb. 1
1:2 DIN
1:1 M200E-SMB
Sollevare
Levantar
Anheben
Fig./Abb. 2
Fig./Abb. 3
Fig./Abb. 4
Fig./Abb. 5
D200-503-00 Honeywell Building Technologies, Building 5 Carlton Park, King Edward Avenue, Narborough, Leicester LE19 3EQ
M201EA-HC
60°C
-20°C
2 1
Rotate Plug
Ruotare Inserire
Girar Conectar
Drehen Einhaken
Clip / Agganciare
3
Acoplar / Einrasten
3 1
Lift Push down
Premere
Precionar
hacia abajo
Runterdrücken
Rotate / Ruotare
2
Girar / Drehen
M201EA-HC
M201EA-HC
M201EA-HC
Fig./Abb. 6
(i)
+
(iii)
EN
FOR THE M201EA-HC OUTPUT MODULE
This manual is intended as a quick reference installation guide. Please refer to the
M201EA-HC
control panel manufacturers installation manual for detailed system information.
The M200 series of modules are a family of microprocessor controlled interface
devices permitting the monitoring and/or control of auxiliary devices. The M201EA-
HC is an output module that allows the control of auxiliary devices such as fire
shutters or sounders.
A single tri-colour LED indicates the status of the module. In normal conditions, the
M200E-SMB
LED can be set by command from the control panel to blink green when the module is
polled. When the control panel switches the relay to the energised state the LED can
be set to continuous green.
SPECIFICATIONS
Operating Voltage Range:
Maximum Standby Current
LED Current (Red):
LED Current (Yellow):
Isolator features:
Humidity:
Maximum Wire Gauge
INSTALLATION
Note: These modules must only be connected to control panels using compatible
proprietary analogue addressable communication protocols for monitoring and control.
M200 series modules can be mounted in several ways (See Figure 1):
1:1 An M200E-SMB custom low profile surface-mounting box. The SMB Base is
affixed to mounting surface, and then the module and cover are screwed onto
the base using the two screws supplied. Box dimensions: 132 mm (H) x 137 mm
(W) x 40 mm (D)
1:2 The DIN bracket on top allows mounting onto standard 35 mm x 7.5 mm "Top Hat"
DIN rail inside a control panel or other suitable enclosure. Install and remove as
shown in Figure 1:2.
Wiring to all series M200 modules is via plug in type terminals capable of supporting
conductors up to 2.5 mm²
Disconnect loop power before installing modules or sensors.
The module address is selected by means of rotary decade address switches (see
Figure 5). A screwdriver should be used to rotate the wheels to select the desired
address, either from the front or the top of the module. (Note: The number of addresses
available will be dependent on panel capability, check the panel documentation for
information on this.)
Short Circuit Isolators
All M200 series modules are provided with short circuit monitoring and isolators on the
intelligent loop. If required the isolators may be wired out of the loop to facilitate the
use of the modules on high current loaded loops, for example if sounders are used.
To do this, the loop out positive should be wired to terminal 4 rather than terminal 2.
See the relevant wiring diagram for details.
M201EA-HC WIRING
The M201EA-HC can be wired for either Supervised (Figure 3) or Non-Supervised
(Figure 4) operation respectively.
M201EA-HC Single Output Module with Supervised Output
This module has two methods of supervision selectable through terminal 5: Standard
Mode, using a 47kOhm resistor EOL (M200-EOL-R), or High Current Mode, using
a 47Ohm resistor in series with a diode EOL (M200-EOL-RD). When the module is
used in supervised mode and power is supplied to the module, a switched negative
input on terminal 12 can be used to signal an external fault condition, such as a power
supply fault. Loss of power is also supervised in this mode such that if the supply
voltage falls below 7V a fault indication is achievable. Note that the use of this fault
mode is dependant on panel software. Please contact the panel manufacturer for
further details.
PSU monitoring is not available when the module switches the output to Alarm.
(ii)
0786
22
INSTALLATION INSTRUCTIONS
15 to 32VDC (Min 16.5VDC for LED operation)
185 µA - No Communication
1.5 mA
5.5 mA
see S00-7100
5% to 95% relative humidity (non-condensing)
2.5 mm²
CAUTION
CAUTION
Electrostatic Sensitive Device
Observe precautions when handling and making connections
Honeywell Products and Solutions Sàrl
DOP-IOD069
(Trading as System Sensor Europe)
EN54-17: 2005
Zone d'activités La Pièce 16
EN54-18: 2005
CH-1180 ROLLE, Switzerland
I56-4411-000