Grote 78200 Guia De Instalacion página 3

Programming is optional. If the default settings are acceptable, skip to the Operation section.
Programmable features include the following:
• Pattern Selection (both WARN and Traffic Directing Patterns)
• Phase Selection (which heads alternate from one another)
• Selective Head Enable (which heads activate)
• Resetting the Factory defaults
Basic Pattern Selection
The first step in programming is to select a basic pattern for each of the 2 modes:
• Warn Function (ORANGE w/RED)
• Traffic Directing Patterns: L, R, and C-O (GREEN w/YELLOW, WHITE w/BROWN, or Both)
1. Connect the RED wire to power and the BLACK wire to Ground.
2. Activate the function you wish to program by connecting the corresponding wire to +12VDC.
3. Touch and release the GREEN w/RED wire to +12VDC
to scroll through the patterns shown to the right.
Note: At any time, you can shortcut to the patterns with
the asterisks by holding the pattern select wire to
+12VDC for the indicated time.
4. Repeat for each function you wish to program.
Please note: All SAE J595 approved patterns need to be configured
properly to ensure compliance with those specifications.
Phase Selection
(Programmable for Patterns 1-18 only)
Each head has two Phases, an "On" phase and an "Off" phase. All of the heads set for Phase A will illuminate at the same time and flash opposite from all of
the ones set for Phase B.
Prior to changing the Phase for any functions, please note the following limitations:
• The Phase option is only programmable for the Warn Pattern.
• It is not programmable for the directional functions (Left, Right, or Center Out).
• There are 5 different Phase options, allowing you to customize which heads flash On together and which are Off together.
• The Phase option is only compatible with Warning Patterns 1-18. You cannot alter the Phases for patterns 19-34 (the pre-set phase is crucial to the
pattern).
1. Activate the Warn function.
2. Place the light in Phase Programming Mode by holding the Pattern Select wire to +12VDC until the unit flashes once, then twice, then three times, then
four times, then five times (15 seconds).
3. Scroll through the 5 Phase variations by touching and releasing the Pattern Select wire to GROUND (or Battery Neg).
4. Disconnect power when you are on the Phase you wish to select.
Pattern Programming
Patterns for Traffic Director
(8– and 6-Head Only)
Left, Right, and Center Out functions
all use the same pattern
1 Standard *
2 6-Head TD with End Flash
3 Standard w/End Blink
4 Two-Head Traveling
5 Progressive (SAE) **
6 Fast Progressive (SAE)
7 Four Head Traveling (SAE)
8 Snake (SAE)
9 Snake Pop
10 Pop
11 Arrowhead on Ends (SAE)
12 Marquee
* Shortcut Pattern #1 (3 sec/1 flash)
** Shortcut Pattern #2 (6 sec/2 flashes)
4-HEAD UNITS
6-HEAD UNITS
-3-
Warn Patterns
1 Flicker *
2 Slow Singleflash
3 Fast Singleflash
4 Slow Doubleflash
5 Fast Doubleflash
6 Slow Tripleflash
7 Fast Tripleflash
8 Quadflash
9 Quintflash
10 Tripleflash w/Post Pop
11 Quadflash w/Post Pop
12 Quintflash w/Pre Pop
13 ECE Doubleflash
14 ECE Quadflash
15 Singleflash Flicker **
16 Doubleflash Flicker
17 Single, Quad w/Post Pop, Flicker
18 Delta-Omega
19 Random 1
20 Random 2
21 Random 3 ***
22 Flashing Bounce
23 Full Bounce
24 Split Bounce
25 Half Bounce
26 Bounce w/End Pop
27 Search Lights
28 Eyeballz
29 Fade Invert
30 Moving Out
31 Triple In/Triple Out
32 Two Speed
(Pursuit default)
33 Random 4
34 Delta X
* Shortcut Pattern #1 (3 sec/1 flash)
** Shortcut Pattern #2 (6 sec/2 flashes)
*** Shortcut Pattern #3 (9 sec/3 flashes)