Important Safety Instructions; General Specifications - Milwaukee 2212-20 Manual Del Operador

Probador automático de voltaje/continuidad y probador automático de voltaje/continuidad con resistencia
Ocultar thumbs Ver también para 2212-20:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

IMPORTANT SAFETY INSTRUCTIONS

WARNING
READ ALL SAFETY WARNINGS AND INSTRUCTIONS.
the warnings and instructions may result in electric shock, fi re and/or serious injury, as well as
instrument damage and/or damage to the equipment being tested. Save these instructions - This
operator's manual contains important safety and operating instructions for the MILWAUKEE
Electrical Testers. Before using, read this operator's manual and all labels on the Electrical Testers.
DANGER
Never make measurement on a circuit in which voltage over 600V rms exists. Use only leads
rated 600V CAT IV or better.
Do not apply more than the rated voltage, as marked on the Tester, between terminals or
between any terminal and earth ground.
Do not attempt to make measurement in the presence of fl ammable gases. Otherwise, the use
of the instrument may cause sparking, which can lead to an explosion.
Never attempt to use the instrument if its surface or your hand is wet.
Do not exceed the maximum allowable input of any measuring range.
Only test on unenergized circuits unless absolutely necessary.
Check tool functionality on a known circuit fi rst. Never assume tool is working. Assume circuits
are live until they can be proven de-energized.
Never open the Battery cover during a measurement.
Do not ground yourself while measuring. Avoid body contact with earthed or grounded sur-
faces such as pipes, radiators, ranges and refrigerators.
This instrument is to be used only in its intended applications or conditions. Otherwise, the instru-
ment's safety functions may not work, resulting in serious personal injury and instrument damage.
To reduce the risk of injury from shock and arc blasts, always wear personal protective
equipment where live conductors are exposed.
WARNING
Never attempt to make measurement if any abnormal conditions, such as broken case and
exposed metal parts are found on the instrument.
Comply with local and national safety requirements when working in hazardous locations.
Keep fi ngers behind the guards and away from test lead tips during measurements.
Do not change the slide switch position (Cat. No. 2213-20) while the test leads are being con-
nected.
Verify proper operation on a known source before use or taking action as a result of the in-
dication of the instrument.
Do not install substitute parts or make any modifi cation to the instrument. For repair, return
the tool to a factory Service/Sales Support Branch or authorized service station.
Do not try to replace the batteries if the surface of the instrument is wet.
Disconnect all the cords and cables from the object under test and power off the instrument
before opening the Battery Cover for Battery replacement.
This tool is designed to be powered by 2- AAA batteries properly inserted in the Milwaukee
Electrical Tester. Do not use with any other voltage or power supply.
Install battery according to polarity (+ and –) diagrams.
Do not leave batteries within the reach of children.
Do not mix new and used batteries. Do not mix brands (or types within brands) of batteries.
Properly dispose of used batteries.
Do not incinerate or dismantle batteries.
Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact
accidentally occurs, fl ush with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
Failure to follow
2
CAUTION
Set the Slide Switch (Cat. No. 2213-20) to an appropriate position before starting measurement.
Disconnect test leads from test points before changing the slide switch function (Cat. No.
2213-20).
Never connect to a source of voltage with the tester OFF or slide switch position in Ω (Cat.
No. 2213-20).
Firmly insert the test leads.
Do not expose the instrument to the direct sun, high temperature and humidity or dew fall.
Altitude 2000m or less. Appropriate operating temperature is within 0ºC and 50ºC.
Keep away from excess dust and water.
Be sure to power off the instrument after use. When the instrument will not be in use for a long
period, place it in storage after removing the batteries.
Use a damp cloth or neutral detergent for cleaning the instrument. Do not use abrasives or
solvents.

GENERAL SPECIFICATIONS

Maximum voltage between
600V CAT IV
any terminal and earth ground
Temperature
Operating: 0°C to 50°C (32°F to 122°F)
Storage: -10°C to 60 °C (-14°F to 140°F)
Operating Altitude
2,000 m
Drop Test
1 m
Battery
2 AAA, NEDA 24 A,IEC LR03
Battery Life
Approx. 20 Hours normal use
Safety Compliances
UL/CSA/IEC/EN 61010-1 3rd Edition and IEC/EN 61010-2-033 1st
Edition (Meter), UL/CSA/IEC/EN 61010-031 1st Ed + A1 (Probes).
Measurement Category IV, 600V, Pollution Degree II,
EMC EN 61326-1.
Certifi cations
cULus, CE
Function
Range
Voltage AC
5 - 600 V
2 - 199.9 V
Voltage DC
200 - 600 V
Resistance
2 - 20 kΩ
Continuity Buzzer
Continuity
0 - 20 kΩ
Accuracy specified as ±(% of reading + 5 digits)
* Input impedance AC/DC Voltage : 300 kΩ
* Overload protection:
For 2212-20 - Meter protected for inputs above rated voltage AC/DC 600 V
For 2213-20 - Function Switch at
, Meter protected for inputs above rated voltage AC/DC 600 V
Function Switch at Ω , Meter protected for inputs above rated voltage AC/DC 420 V
* Test leads rated for 10A with: measurement time 30 seconds maximum, rest time 20 minutes minimum,
40°C ambient.
FUNCTIONS
Resolution
Accuracy
1 V
±(3.0% + 5 dgt)
0.1 V
±(3.0% + 5 dgt)
1 V
±(3.0% + 5 dgt)
0.01 kΩ
±(3.0% + 5 dgt)
Continuity Buzzer sounds
at 20 kΩ or less
3

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

2213-20

Tabla de contenido