Publicidad
Enlaces rápidos
Publicidad
Manuales relacionados para MW MOUNTS Medium - Large Full Motion Mount
Resumen de contenidos para MW MOUNTS Medium - Large Full Motion Mount
- Página 1 Medium - Large Full Motion Mount INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES MANUEL D’ INSTRUCTIONS MOUNTS CAUTION: THE MAXIMUM LOADING WEIGHT IS 70 LBS. USE WITH PRODUCTS HEAVIER THAN THE MAXIMUM WEIGHT INDICATED MAY RESULT IN INSTABILITY AND POSSIBLE PERSONAL INJURY.
-
Página 2: Tools Needed
QUESTIONS? NEED HELP? PLEASE CALL MOUNTS 1-602-674-1000 DISCLAIMER – WARNING INFORMATION Disclaimer –. MW PRODUCTS has extended every effort to ensure to accuracy and completeness of this manual. However, MW PRODUCTS does not claim that the information covers all installation and or operational variables. The information contained in this document is subject to change without notice or obligation of any kind. Regarding the information contained herein, MW PRODUCTS makes no representation of warranty, expressed or implied, and assumes no responsibility for accuracy, sufficiency, or completeness of the information contained in this document. - Página 3 MONITOR PLATE AND ADAPTERS Use diagrams to determine which mounting configuration is needed to attach Monitor Plate (with or without adapters) to the back of flat panel. Please check flat panel wall mounting compatibility before proceeding with installation. Pay attention to below for the correct installation pattern of adapters A and B.
- Página 4 HARDWARE PART NUMBERS M4 x 30 M6 x 30 M8 x 30 M4 x 12 M6 x 15 M8 x 15 M8 x 45 PHILLIPS LAG BOLT WALL SQUARE 10mm STEEL SCREWS 8mm x 65mm ANCHOR WASHER SPACER SPACER WASHER PRODUCT COMPONENT PARTS Product Components Contents...
- Página 5 STEP 1- REMOVE MONITOR PLATE FROM MOUNT Remove and save Phillips head screws and washers. Screws and washers will be used to reattach monitor plate in step 5. STEP 2A- MONITOR PLATE ATTACHMENT Connect monitor plate to flat panel Conecte el adaptador al monitor Connectez l'adaptateur au moniteur...
- Página 6 STEP 2B- MONITOR ADAPTERS ATTACHMENT TO MONITOR PLATE Connect monitor plate with adapters to flat panel (if necessary) Conecte el adaptador al monitor Connectez l'adaptateur au moniteur Note: See page 3 for other monitor plate configurations. STEP 2C- CURVED BACK FLAT PANEL (MONITOR PLATE) Connect monitor plate to flat panel Conecte el adaptador al monitor Connectez l'adaptateur au moniteur...
- Página 7 STEP 2- USE M8 STEEL WASHER IF THE PHILLIPS SCREWS FROM THE MONITOR KIT ARE TOO LONG Diagrams show three options for using additional washers if hardware screws are too long to properly tighten into back of flat panel television. B or C B or C B or C...
- Página 8 STEP 3A- WOOD STUD (CONCRETE INSTALLATION SKIP TO 3B) Find stud and mark edge and center locations Ubique el panel y marque las ubicaciones de los bordes y el centro. DRILL BIT Repérez l'emplacement d'une poutre, puis marquez l'emplacement des bords et du centre de cette poutre. NOT INCLUDED STEP 3A- DRILL PILOT HOLES AND MOUNT WALL PLATE Mount wall plate...
- Página 9 STEP 3 B – SOLID CONCRETE Drill pilot hole Solid Concrete Realice el agujero piloto Concreto sólido Percez le trou de guidage Béton massif DRILL BIT NOT INCLUDED 3/8” STEP 3B – DRILL PILOT HOLE AND MOUNT WALL PLATE Ratchet Handle Secure top lag bolt first.
- Página 10 STEP 4 – SNAP PLASTIC END CAPS ON TOP AND BOTTOM OF WALL PLATE...
-
Página 11: Locking Mechanism
STEP 5- ATTACH PANEL TO MOUNT Hang with monitor attached Heavy, Assistance Cuelgue con el monitor adherido. Required Accrochez avec le moniteur installé. TRES LOURD ! Cette etape requiert deux personnes !PESADO! Necesitara ayuda para realizar esta operacion STEP 5- ADJUST TILT TENSION/ POST INSTALLATION LEVEL Locking mechanism Mecanismo de fijación Mécanisme de verrouillage... -
Página 12: Warranty Information
Congratulations! Installation complete WARRANTY INFORMATION This warranty applies to US Residents who purchase from an authorized MW PRODUCTS Dealer. MW PRODUCTS products are covered against defects in materials and workmanship for 5 years. MW PRODUCTS will repair or replace the defective component or product, at its sole discretion. Failure to follow product care instructions from MW PRODUCTS will result in void of warranty.