Descargar Imprimir esta página

Hart HLPM01 Manual Del Operador página 13

Publicidad

Idiomas disponibles

Idiomas disponibles

MAINTENANCE
WARNING:
Before performing any maintenance or cleaning the lawn
mower, make sure the mower blades come to a complete
stop and the batteries and start key are removed to avoid
accidental starting and possible serious personal injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
When servicing, use only authorized replacement parts.
Use of any other parts can create a hazard or cause
product damage.
WARNING:
Never use a hose, water, or any liquids to clean or
rinse off the lawn mower. Corrosive liquids, water, fer-
tilizers, and chemicals used to treat lawns can enter the
lawn mower and/or battery compartment and damage
electronic components and/or the battery pack, which
can result in a short circuit, increased risk of fire, and
serious personal injury. Remove any buildup of grass
and leaves on or around the mower housing and/or un-
derneath the mower deck. Wipe the mower clean with
a dry cloth occasionally.
NOTICE:
Periodically inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please contact customer service or an
authorized service center for assistance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics
are susceptible to damage from various types of commercial
solvents and may be damaged by their use. Use clean cloths
to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petro-
leum-based products, penetrating oils, etc., come in
contact with plastic parts. Chemicals can damage,
weaken, or destroy plastic which can result in serious
personal injury.
NOTICE:
Never use a hose, water, or any liquids to clean the lawn
mower, as water can damage electronic components
and the battery pack. Remove any buildup of grass and
leaves on or around the motor cover. Wipe the mower
clean with a dry cloth occasionally.
LUBRICATION
All of the bearings in this product are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further bearing
lubrication is required.
WARNING:
Always protect hands by wearing heavy gloves and/or
wrapping the cutting edges of the blade with rags and
other material when performing blade maintenance. Con-
tact with the blade could result in serious personal injury.
REPLACING THE CUTTING BLADE
See Figures 15 - 16.
NOTE: Only use authorized replacement blades.
 Stop the motor and remove the start key. Allow blade to
come to a complete stop.
 Remove the battery pack from the battery port.
 Turn the mower on its side.
 Wedge a block of wood between the blade and mower
deck to prevent the blade from turning.
 Loosen the blade nut by turning it counterclockwise (as
viewed from bottom of mower) using a 15 mm wrench or
socket (not provided).
 Remove the blade nut, spacer, blade insulator, and blade.
 Place the new blade on the shaft against the blade posts.
Ensure blade is properly seated with shaft going through
center blade hole and the two blade posts inserted into their
respective holes on the blade. Make sure it is installed with
the curved ends pointing up toward the mower deck and
not down toward the ground. When seated properly, the
blade should be flat.
 Replace the blade insulator and spacer, then thread the
blade nut on the shaft and finger tighten.
NOTE: Make certain all parts are replaced in the exact order
in which they were removed.
 Torque the blade nut down clockwise using a torque wrench
(not provided) to ensure the bolt is properly tightened. The
recommended torque for the blade nut is 310 – 360 in.lbs.
WARNING:
Ensure blade is properly seated and the blade nut is
tightened to the torque specifications above. Failure to
properly attach the blade could cause it to come loose
and result in possible serious personal injury.
9 – English

Publicidad

loading