Publicidad
Idiomas disponibles
Idiomas disponibles
convector in the event of excessive temperature convector (due to clogged vents, fan
malfunction ) . In this case, disconnect the unit from the power supply , waiting a few
minutes and remove the cause of overheating,
21. Do not touch the hot parts of the convector . Do not touch the appliance with wet hands.
22. In the case of wet convector or falling of any object through the ventilation grille of the
convector , turn it off immediately and disconnect from the network. Before re- use
with convector call for service .
23. Do not place the convector directly below the electrical outlet.
24. Always turn off the convector button before disconnecting it from the mains.
25. Do not use this heater in the immediate vicinity of a bathtub, shower or swimming pool
26. Do not use this heater if it has been dropped
27. Do not use if there are visible signs of damage to the heater
28. Use the heater on a level and stable surface or attach it to the wall, if provided for by the
manufacturer
WARNING: Do not use this heater in small rooms where there are people who are unable
to leave them by themselves, unless constant supervision is ensured.
WARNING: To reduce the risk of fire, keep textiles, curtains or other flammable materials at
least 1 m away from the heater air outlet.
"Caution Hot Surface" - The temperature of accessible surfaces may be higher when the equipment is in operation, which
means that the housing elements become hot during operation during operation, BE CAREFUL !!!
WARNING: In order to avoid overheating - do not cover the heater. The device is not to be covered with clothing, blankets
and other textile products which could cause ignition.
BEFORE FIRST USE
In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
This device should only be placed on a firm level surface and a minimum 50cm distance from walls or any other objects. It is a way to
optimize air flow, avoid placing the device in corners and small spaces.
Product description: Tower fan heater
1. LCD panel
3. Air outlet grid
5. Handle
7. Power switch
9. Remote control
11. Temperature decrease button
13. Heat setting button
15. Temperature increase button
17. Heat indicator: level I – 1200W
19. Timer indicator
21. Desired temperature level
USAGE
1. Ensure the power switch (7) is off. Insert the plug into a suitable power outlet and turn the power supply on by power (7) located at the
back of the device. The device is in standby mode.
2. When in standby mode, only power button (10) on control panel will respond your touch. Turn on the device by pressing the power
button (10) on either the remote or control panel. The device will blow cold air by fan function illustrated by fan indicator (16).
3. Press the Heat setting button (13) once to operate low heating mode 1200W, or twice to operate high heating mode 2200W. You can
see one sun (17) or two suns (17+18) at control panel. After 10 minutes all displayed symbols will be turn off automatically.
4. To turn off the device press the power button (10). Please note: the unit will take approximately 30 seconds to stop blowing out air. Turn
off the power switch (7) at the back of the unit.
TIMER FUNCTION: The timer function can be used in any mode. The timer allows you to set the length of time from 1-8 hours. To use the
timer, press the timer button (14). Each press of the button increases the time set by 1 hour, at the same moment the timer indicator (19)
will be displayed. The amount of time set will be displayed on the unit, and will count down in 1 hour. If the timer has been set for 8 hours
(MAX amount of time) pressing the button once more will reset the Timer Function.
OSCILLATION FUNCTION: Press the oscillation button (12) to turn on the oscillation function. The device starts to swing left and right
side. At the same time the oscillation indicator (20) will be displayed. Press the oscillation button (12) again to turn off the oscillation
function.
TEMPERATURE SETTING: By pressing buttons (15) and (11) set up desired room temperature.
1. The temperature range is available in the range from 10 to 49 degrees. Press button (15) to increase the desired temperature and
2. Buttons
4. Indication light
6. Air inlet grid
8. Base
10. Power button
12. Oscillation button
14. Timer button
16. Fan indicator
18. Heat indicator: level II – 2200W
20. Oscillation indicator
6
Publicidad
