Publicidad
Idiomas disponibles
Idiomas disponibles
FUNCTION OF THE OPERATION MODES AND INSTALLATION DESCRIPTIONS
A. Accessories
After unpacking, please check whether
the above-mentioned accessories are
included, and check their purposes in
the installation introduction in this
manual. Accessory No. 6 is already
mounted at the bottom of the back of the
machine.
B. Portable air conditioning
G. Appearance and Function of Remote
Control.
Notes:- Do not drop the remote control.-
Do not place the remote control in a
location exposed to direct sunlight.
A. Operation Introduction
Before starting operations in this section:
1)Place the air conditioner in a place where
you have close access to a grounded
electrical outlet.
2) Install the exhaust hose, and adjust the
window position well.
3) Insert the power cord into a grounded
AC220~240V/50Hz socket;
4) Press the POWER button to turn on the
air-conditioner.
5) Press the POWER button to turn on
the air-conditioner.
H, I, and K. Installation of exhaust air hose
M) Temporary installation
1. Twist both ends of the exhaust hose
into the Hose connections.
2. Insert the square fixing clip into the air
outlet at back of the machine.
3. Put the other end of the exhaust hose
near windowsill.
J&K: Window Slider Kit Installation
The installation manner of window slider
kit is mostly in "horizontal" and
"vertical". As shown Fig. 5 and Fig.5a,
check the min. and max. size of the
window before the installation.
1. Install the window kit on the window ;
2. Adjust the length of the window slider
kit according to the window width or
height, and fix it with the dowel;
3. Attach the hose bracket to the hole in
the window rail
O. Internal Tank "Water Full" Alarm
The water tank inside the machine
has a level monitor that detects
when the tank is full. When the container
is full, the machine switches off
automatically and the code E4 is shown on
the display.
(If the water tank is full, please remove
the rubber plug at the bottom of the unit
It is very important that the filter is
cleaned regularly; otherwise the
air conditioner might lose capacity
and even be risk serious damage.
to drain the water.) We recommend that
you drain the water over a floor drain, or
alternatively an oven tray.
when the water is full, please remove
the rubber blockage at the bottom of
unit, and all water will be drained
outside.)
Care Instructions And Maintenance
Declaration:
1) Before cleaning, be sure to
disconnect the unit from any electric
supply outlet;
2) Do not use gasoline or other
chemicals to clean the unit;
3) Avoid rinsing water directly on the unit
4) If the machine is damaged, please
contact your dealer
1. The air filter
-If the air filter becomes clogged with
dust/dirt, the air filter should be
cleaned once every two weeks.
-Dismounting
Open the air inlet grille and take off the air
filter.
-Cleaning
Clean the air filter with a neutral
detergent in lukewarm water( 40°C ) and
Operating Instructions
let dry in the shade.
-Mounting
Putting the air filter into the inlet grille,
replace the components as they were.
2.Clean the surface with a neutral
detergent and a wet cloth, followed by
drying it with a dry cloth.
E. Before using
Check whether the exhaust hose
has been mounted properly.
Cautions for cooling and
dehumidifying operations:
-When using functions on cooling and
dehumidifying, keep an interval of at
least 3 minutes between each
POWER.
-Power supply meets the
requirements.
-The socket is for AC use.
-Do not share one socket with other
appliances.
-Power supply is
AC220-240V, 50Hz
1. Turn on the unit
a) Plug in, then the unit beeps once, " "
The power indicator light is on.
b) Press the "
" button, then the unit is
turned on.
c) The LED displays the room temperature
and under Automatic mode.
2. Cooling operation
-Press the "Mode" button till the
Snowflake icon is displayed on the panel.
+
-
-Press the "
" or "
" button to select
the desired room temperature.
(15°C -31°C )
-Press the "Fan Speed" button to
select wind speed.
3. Dehumidifying operation
Press the "Mode" button till the
"Dehumidify" icon appears.
-Automatically set the selected
temperature to current room
temperature minus 2°C .
-Automatically set the fan motor to
LOW wind speed.
4. Fan operation
-Press the "Mode" button till the "Fan"
icon appears.
-Press the "Fan Speed" button to
GB
13
Publicidad
