Publicidad
Idiomas disponibles
Idiomas disponibles
Multi-function Switch (2)
Use the multi-function switch to select different operating
modes:
Appliance off / charging mode
I
Appliance on in battery mode
II
Appliance on in 12 V power supply mode with connec-
tion cable
Nozzle Attachments
The various nozzle attachments are easy to attach and
detach.
Charging the Built-in Battery
1. Switch off the appliance.
2. Connect the power supply unit to the connection
socket (4).
3. Connect the power supply unit to an approved power
outlet. Charge the appliance for 12 hours before using it
for the first time.
- The indicator light lights up red during charging.
- The light gives no indication of the battery's charge
status.
- It is normal for the appliance to heat up during
charging.
4. Stop any charging operation after a maximum of
12 hours.
CAUTION:
Always disconnect the mains plug from the socket after
charging.
Using the Appliance
Operation with Rechargeable Battery
1. Disconnect the appliance from the power supply unit.
2. Attach a nozzle if necessary.
3. Use the multi-function switch to turn the appliance on ( I )
or off ( ).
12 V Power Supply
Irrespective of the charging level of the battery, you may use
the appliance at any time with 12 V power supply.
1. Turn off the appliance. If necessary, disconnect the
appliance from the power supply.
2. Press the button to open the cable storage compartment.
Extract the cable.
3. Close the cable storage compartment. Pay attention to
the cable guide in the cover.
4. Connect the connecting cable to an automobile auxiliary
power outlet for 12 V. The control lamp on the plug lights
up as soon as power is available. If necessary, turn on
the ignition of your car.
AKS713CB_IM_04.2023
5. Use the multi-function switch to turn the appliance on ( II )
or off ( ).
Vacuuming Dry Dirt
• Only vacuum up dry dirt with a dry collection container
and a dry filter!
• Attach one of the two crevice nozzles (8 / 9). On top of
that, you can also attach the brush tool.
Picking up Wet Dirt or Liquids
1. Empty the collection container before vacuuming liquids
or wet dirt.
2. Fit the attachment for wet vacuuming (13) or one of the
two crevice nozzles (8 / 9).
3. Note the MAX marking on the collection container. The
maximum collection amount is 100 ml.
4. If you want to remove the nozzle, hold the end of the
nozzle down. In this way you avoid unintentional leakage
of the liquid.
End of Use
1. Switch off the appliance.
2. Empty the collection container as described below. Clean
the filter insert after each use to restore the appliance to
full performance the next time it is used.
3. Then recharge the accumulator of the appliance.
Maintenance and Cleaning
WARNING:
• Always disconnect the appliance from the power sup-
ply unit before maintenance and cleaning!
• If necessary, disconnect the appliance from the 12 V
connection cable before cleaning.
• Never immerse the motor housing in water for clean-
ing. It could cause an electric shock or fire.
CAUTION:
• Do not use a wire brush or other abrasive objects.
• Do not use sharp or abrasive cleaning agents.
• The individual components are not suitable for clean-
ing in the dishwasher.
• Never wash the filter in the washing machine.
• The housing can be wiped clean with a slightly damp
cloth.
• You can wipe the power supply unit with a dry cloth.
Emptying the Collection Container
1. If necessary, remove the nozzle from the appliance.
2. Hold the appliance horizontally when removing the
collection container.
3. Press the button (1) to release the collection container.
4. First pull the permanent filter out of the collection con-
tainer and then the filter cover.
9
19.04.23
Publicidad
