Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
8-FT INDUSTRIAL LED WHITE STRIP LIGHT FIXTURE
WITH 4 T8 LED TUBES
INSTALLATION INSTRUCTIONS
Please read carefully and save these instructions.
electrical shock or fire, which may cause injury or death.
WARNING – RISK OF FIRE: Turn off the main power at the circuit breaker before
installing the fixture, changing lamps, or performing other maintenance in order to
prevent possible shock.
All electrical connections must be in accordance with local, and national electrical
codes.
Prior to installation it is important to follow the following guidelines:
A. Use only the type of tube light specified, with wattage not greater than
specified on the wattage label found on the fixture.
B. Remove all protective plastic film covering from the fixture.
Failure to do so may lead to
________
CAUTION
_________
GENERAL
PARTS INCLUDED
(not shown to actual size)
Wire Nuts x 3
¾ in. Metal Retainer
Clip x 6
PARTS MAY BE REQUIRED (NOT INCLUDED)
Wire and Metallic Conduit Installation
14/3 Solid CU Lighting
4 in. Flat Square
Flexible Whip (BX
Cover with ½ in.
Cable) (Includes
Knockout
Metallic Fittings) (w/ ½
in. fittings)
Cord With Plug Installation
3-wire Dishwasher
4 in. Square
Power Plug w/
Single Device
Fitting
Mud Ring, ½ in.
(SJO Cord)
Raised
Hardwired Cord Installation
16/3 600-Volt CU
4 in. Flat Square
Flexible Portable
Cover with ½ in.
Power SOOW Cord
Knockout
(or SJO Cord)
STCONN1 –
sold separately
Lamp
J-Box
Holder
Cover x 2
Assemblies
Screws x 2
x 8
T8 Lamp x 4
or
4 in. Flat Octagon
Cover with ½ in.
Knockout
or
4 in. Octagon
15 Amp Residential
Single Device
Grade Self
Mud Ring, ½ in.
Grounding Duplex
Raised
Outlet
or
1/2 in. Non-Metallic
Twin-Screw Cable
4 in. Flat
Clamp Connectors x2
Octagon Cover
with ½ in.
Knockout
5 in. Strip
Connector
1
Publicidad
Manuales relacionados para Envirolite T8
Resumen de contenidos para Envirolite T8
- Página 1 Screws x 2 8-FT INDUSTRIAL LED WHITE STRIP LIGHT FIXTURE ¾ in. Metal Retainer T8 Lamp x 4 WITH 4 T8 LED TUBES Clip x 6 PARTS MAY BE REQUIRED (NOT INCLUDED) Wire and Metallic Conduit Installation 14/3 Solid CU Lighting 4 in.
- Página 2 Remove the end caps from the channel. Fig. 1 chain to the ceiling via your Part A Part B Remove the 4 T8 lamps and put them preferred mounting option (Fig. 4) aside in a safe place. Fig. 4 NOTE: Due to safety regulations, the...
- Página 3 _________________________________ ______________________ WIRING USING A CORD CONNECTION FINISHING INSTALLATION BLACK FIXTURE WIRE BLACK SUPPLY WIRE With the power off, connect the NOTE: Use either a square or an octagonal outlet box cover black supply wire to the two black WHITE FIXTURE depending on the shape of your outlet box.
- Página 4 TIRA LED INDUSTRIAL BLANCA DE 8 PIES LÁMPARA Clips de retención de metal de ¾ pulgadas x6 CON 4 TUBOS DE LED T8 Lámpara T8 x 4 PARTES NECESARIAS (NO INCLUIDO) Instalación de Cables y Conductos Metálicos Látigo flexible 14/3 de...
- Página 5 Conecte una cadena (no incluido) a Retire las tapas de los extremos del canal. cada gancho, luego fije cada cadena Retire las 4 lámparas T8 y déjelas a un al techo a través de su opción de lado en un lugar seguro.
- Página 6 __________________________________________________ __________________________ CABLE NEGRO DE INSTALLACION UTILIZANDO UNA CONEXIÓN DE CORDÓN TERMINANDO LA INSTALACION ALIMENTACIÓN CABLE NEGRO DEL LUMINARIO NOTA: Use una cubierta de caja de salida cuadrada u octogonal dependiendo de la Con el potencia apagada, conecte el cable forma de su caja de salida.
- Página 7 Clips de retenue en LAMPE À BANDE À DEL INDUSTRIELLE BLANCHE DE 8 métal ¾ po. x 6 Lampe T8 x 4 PIEDS AVEC 4 TUBES LED T8 PIÈCES NÉCESSAIRES (NON INCLUSES) Installation De Fils Et De Conduits Métalliques 14/3 fouet flexible...
- Página 8 Insérez un crochet (non incluse) dans Retirez les capuchons des extrémités du chacun des quatre trous aux coins de Fig. 1 canal. Retirez les 4 lampes T8 et mettez- l'accessoire. les de côté dans un endroit sûr. Attachez une chaîne (non incluse) à...
- Página 9 ______________________ ___________________________________________ FINITION INSTALLATION FIL D'ALIMENTATION CÂBLAGE À L'AIDE D'UNE CONNEXION DE CORDON NOIR FIL DU LUMINAIRE NOIR Avec l'alimentation éteinte, connectez le fil REMARQUE: Utilisez un couvercle carré ou octogonal en fonction de la forme de votre noir de l'alimentation au fil noir du luminaire. FIL D'ALIMENTATION boîte de sortie.