IVT AG-150-RC Manual De Instrucciones página 10

Instruction manual
ATTENTION! DANGER OF ELECTRIC
SHOCK!
EN
Consider working area environment. Do not expose
power tools to rain. Do not use power tools in damp
or wet locations. Keep work area well lit and dry. Try
to prevent the device from getting wet or being
exposed to humidity. Do not leave it outside
overnight. Water entering a power tool will increase
the risk of electric shock.
∙
The power supply cable should be checked regularly
and, before using it, make sure the cable is not damaged
or worn out. If the cable is not in good condition, do
not use the appliance; take it to an authorized service
centre.
∙
When tool is used outdoor, only use an extension
cable that is suitable for outdoor use and which is
marked for this specific use. Keep it away from the
working area, from damp, wet or oily surfaces and away
from heat and flammable materials.
∙
Avoid any accidental starting: make sure that the
power switch (if present) is in the «off» position, before
plugging the tool in.
∙
Remove adjusting keys or wrenches before turning
the tool on.
∙
Do not use the tool if the switch does not turn the
tool on or off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
WARNING! During the use of certain
power tools, some dust containing
chemicals known to cause cancer,
may occur.
Some of these chemicals are: lead from lead based
paints, crystalline silica from bricks and cement and other
masonry products, arsenic and chromium from chemically
treated lumber and other dangerous products. If dust is
present, your risk from these exposures varies,
depending on how often you do this type of work. To
reduce your exposure to these chemicals, any time
you do pulverulent operations, work in a well
ventilated area and work with approved safety
equipment, such as dust masks that are specially
designed to filter out microscopic particles.
∙
If the appliance strikes a foreign body, examine the
device for signs of damage and carry out any necessary
repairs before restarting and continuing to work.
∙ If the appliance starts to vibrate abnormally, turn it
off and check for the cause immediately. Vibration is
generally a warning of trouble.
∙ Always switch off the appliance and wait until the
All manuals and user guides at all-guides.com
device completely stops whenever you leave the
machine, before carrying out maintenance, before
checking, cleaning or working on the appliance.
∙ It is forbidden to move or modify any of the internal
parts of the device.
Specific safety rules
∙ Large variation of temperature can lead to
condensation on «live» part. Give the machine time to
adjust to the temperature of the area.
∙ Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
∙
The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool.
∙ Incorrectly sized accessories cannot be adequately
guarded or controlled.
∙
The arbour size of the wheel, flanges or any other
accessory must properly fit the spindle of the power tool.
∙
Do not use damaged accessories.
∙ Do not use accessories that require liquid coolants.
∙ Maintain a firm grip on the power tools and position
your body and arm to allow you to resist kickback forces.
Always use auxiliary handle for maximum control over
kickback or torque reaction during start-up.
∙
Do not position your body in line with, behind or near
the rotating wheel.
∙
Do not position your body in the area where power
tool will move if kickback occurs.
∙ Use special care when working corners and edges.
∙
Don't restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter
the cut. The wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
∙ Support panels or any other oversized workpiece to
minimize the risk of wheel pinching and kickback. Large
workpieces tend to sag under their own weight.
∙ Use caution when making a cut into existing walls or
other blind areas. The protruding wheel may cut gas or
water pipes, electrical wiring or objects that can cause
kickback.
∙ Never lay the power tool down until the accessory
has come to a complete stop.
∙
Do not run the power tool while carrying it at your
side.
∙
Do not operate the tool near flammable materials.
∙ Do not place your hand near the rotating accessory.
∙ Do not leave the machine in operation while it is
unattended.
UNPACKING
When unpacking, check to make sure that all
components are included. Refer to the drawings on this
10