Publicidad
Idiomas disponibles
Idiomas disponibles
CONvERT TO EDgINg MODE
CAUTION:
The wheeled edge guide should only be used when in the edging mode.
The trimmer can be used in trimming mode or edging mode to trim overhanging grass along lawn
edges and flower beds.
For edging, the trimmer head should be in the position shown in figure K. If it is not:
• Remove the battery from the trimmer.
• Press and hold the head-release button (14) as shown in figure J.
• While holding the auxillary handle (3), rotate the head (6) counterclockwise.
• Release the head-release button.
Note:
The metal shaft and housing will only rotate in one direction.
• To return to trimming position, rotate the head clockwise back to its original position.
• Release the head-release button.
Note:
The Auto Feed System may not operate correctly if wheeled edge guide is not used.
Note: You will experience faster than normal cutting line wear if the edging wheel is positioned
too far from the edge with the cutting line positioned over the sidewalk or abrasive surface.
EDgINg
WARNINg:
When being used as an Edger, stones, pieces of metal and other objects
can be thrown out at high speed by the line. The trimmer and guard are designed to reduce the
danger. However, MAKE SURE that other persons and pets are at least 100 feet (30m) away.
Optimum cutting results are achieved on edges deeper than 2 inches (50 mm).
• Do not use this trimmer to create trenches.
• Using the edging wheel (7), guide the trimmer as shown in figure K.
• Position the edging wheel on the edge of the sidewalk or abrasive surface so the cutting line
is over the grass or dirt area to be edged.
• To make a closer cut, slightly tilt the trimmer.
ACCELERATOR SWITCH & RUNTIME ExTENSION MODE
This string trimmer gives you the choice to operate at a more efficient speed to extend the
runtime for larger jobs, or accelerate the trimmer speed for high-performance cutting (figure L).
• To extend runtime, pull the runtime extender switch (4) back toward the battery (2) into
position #1. This mode is best for larger projects that require more time to complete.
• To accelerate the trimmer, push the runtime extender switch forward toward the trimmer head
(6) into position #2. This mode is best to cut through heavier growth and for applications that
need higher RPM.
NOTE:
When in acceleration mode (#2), runtime will be decreased as compared to when
trimmer is in extended runtime mode (#1).
CUTTINg LINE / LINE FEEDINg
Your trimmer uses .065 inch (1.65 mm) diameter, ROUND nylon line. During use, the tips of
the nylon lines will become frayed and worn and the special self feeding spool will automatically
feed and trim a fresh length of line. Do not bump trimmer on ground in attempt to feed line or for
any other purposes.
• Cutting line will wear faster and require more feeding if the cutting or edging is done along
sidewalks or other abrasive surfaces or heavier weeds are being cut.
REPLACEMENT ACCESSORIES
CAUTION:
Before you begin trimming, only use the appropriate type of cutting line.
Use BLACK+DECKER replacement spool Model No. AF-100, and replacement cap RC-100.
Reload nylon line (either bulk or prewound replacement spool) as shown in this manual.
• USE ONLY .065 inch (1.65 mm) DIAMETER ROUND NYLON MONOFILAMENT LINE. Do
not use serrated or heavier gauge line, as they will overload the motor and cause overheating,
and will not feed properly. This line is available at your local dealer or authorized service center.
• Other replacement parts (guards, spool caps, etc.) are available through BLACK+DECKER
service centers. To find your local service location call: 1-800-544-6986 or visit
www.blackanddecker.com.
WARNINg:
The use of any accessory not recommended by BLACK+DECKER for use
with this trimmer could be hazardous.
REPLACINg THE SPOOL
• Remove battery from trimmer.
All manuals and user guides at all-guides.com
10
Publicidad
