Publicidad
OBJ_BUCH-1797-004.book Page 19 Friday, October 21, 2016 1:54 PM
Technical Data
Angle Grinder
Article number
Rated power input
Output power
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder
spindle
Weight according to EPTA-
Procedure 01:2014
– with vibration-damping auxilia-
ry handle
– with standard-auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Only for power tools without reduced starting current: Starting cycles generate brief voltage drops. Interference with other equipment/machines may
occur in case of unfavourable mains system conditions. Malfunctions are not to be expected for system impedances below 0.25 ohm.
Noise/Vibration Information
Sound emission values determined according to EN 60745-2-3.
Typically the A-weighted noise levels of the product are: Sound pressure level 92 dB(A); Sound power level 103 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K determined
h
according to EN 60745-2-3:
Surface grinding:
a
h
K
Disk sanding:
a
h
K
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Bosch Power Tools
GWS ...
20-180 H
3 601 H49 L..
W
2000
W
1250
-1
min
8500
mm
180
M 14
mm
25
kg
5.1
kg
5.0
/II
Assembly
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales ser-
vice agent for maintenance. For addresses, see section "Af-
ter-sales Service and Application Service".
Protection Guard for Grinding
Place the protection guard 5 on the spindle collar. Adjust the
position of the protection guard 5 to the requirements of the
operation and lock the protection guard 5 with the locking
screw 6.
Adjust the protection guard 5 in such a manner that
sparking is prevented in the direction of the operator.
20-230 H
21-180 H
3 601 H50 L..
3 601 H51 L..
2000
2100
1250
1350
6600
8500
230
180
M 14
M 14
25
25
5.4
5.1
5.3
5.0
/II
/II
3 601 ...
H49 L..
H50 L..
2
m/s
2
m/s
2
m/s
2
m/s
1 609 92A 2C6 | (21.10.16)
English | 19
21-230 H
3 601 H52 L..
2100
1350
6600
230
M 14
25
5.4
5.3
/II
H51 L..
H52 L..
9.5
9.5
1.5
1.5
5.5
4.0
1.5
1.5
Publicidad
