Lighting Instructions; To Turn Off Gas To Appliance - Empire GWT-25-2 Instrucciones De Instalación Y Manual Del Propietario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
A. This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these instructions
exactly.
B. BEFORE LIGHTING smell all around the appliance
area for gas. Be sure to smell next to the floor because
some gas is heavier than air and will settle on the
floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
1. STOP! Read the safety information above.
2. Set the thermostat to lowest setting.
3. Turn off all electric power to the appliance (if appli-
cable).
4. Remove control access panel (control door).
5. Push in gas control knob slightly and turn
clockwise
GAS CONTROL KNOB SHOWN IN "OFF" POSITION
NOTE: Knob cannot be turned from "PILOT" to "OFF"
unless knob is pushed in slightly. Do not force.
6. Wait ten (10) minutes
Then smell for gas, including near the floor. If you smell
gas, STOP! Follow "B" in the safety information above.
If you don't smell gas, go to the next step.
1. Set the thermostat to lowest setting.
2. Turn off all electric power (if applicable) to appliance
if service is to be performed.
3. Remove control access panel (control door).
Page 12

LIGHTING INSTRUCTIONS

causing property damage, personal injury or loss of life.
LIGHTING INSTRUCTIONS
to "OFF."
to clear out any gas.

TO TURN OFF GAS TO APPLIANCE

• If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it; call a qualified
service technician. Force or attempted repair may
result in a fire or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of
the control system and any gas control which has
been under water.
7. Find pilot - follow metal tube
from gas control. The pilot is mounted
on front of main burner.
8. Turn gas control knob coun-
terclockwise
9. Push in control knob all the
way and hold in. Immediately light the pilot with a
match. Continue to hold the control knob in for about
one (1) minute after the pilot is lit. Release knob and
it will pop back up. Pilot should remain lit. If it goes
out, repeat steps 5 through 9.
• If knob does not pop up when released, stop and
immediately call a qualified service technician or
gas supplier.
• If the pilot will not stay lit after several tries,
turn the gas control knob to "OFF" and call your
service technician or gas supplier.
10. Turn gas control knob counterclockwise
"ON."
11. R e p l a c e
c o n t r o l
door).
12. Turn on all electric power to the appliance
(if applicable).
13. Set thermostat to desired setting.
4. Push in gas control knob slightly and turn clockwise
to "OFF." Do not force.
5. Replace control access panel (control door).
to "PILOT."
a c c e s s
p a n e l
( c o n t r o l
12425-9-0107
to

Publicidad

Tabla de contenido
loading

Productos relacionados para Empire GWT-25-2

Este manual también es adecuado para:

Gwt-25-2sgGwt-25-2rbGwt-35-2Gwt-35-2sgGwt-35-2rb

Tabla de contenido