Publicidad
Idiomas disponibles
Idiomas disponibles
3. Make sure the appliance is on OFF stage of main switch.
GB
Connect the appliance to suitable power supply and turn on
the appliance. The default status is "temperature measuring
status".
4. Let the appliance reach the set temperature before putting
the pre-cooled beverages (< 6 °C) to the appliance evenly with
sufficient surrounding spacings to ensure proper air circu-
lation.
5. Close the door properly to keep the best performance.
6. Simply disconnect to switch OFF the appliance. Disconnect
the appliance when not in use.
7. Wait at least 5 minutes before plug in again the after unplug
the appliance or power sudden break.
NOTE:
• If no button is pressed within 30 seconds under any setting
mode (except parameter recovery setting mode), the newly
set temperature will be stored automatically.
• The temperature setting ranges from 0°C to 10°C.
• The height of each shelf can be adjusted according to the
height of the items.
• Do not exceed the maximum shelf load stated in the "Techni-
cal specifications".
User menu
1. Under "temperature measuring status", press "Set button"
button 3s to enter user menu. Only two items could be se-
lected – "St" and "Po".
2. Press "Rst button" to return to the "temperature measuring
status".
Set temperature
1. In user menu, select "St" and press "Set button" to enter the
"temperature setting mode", press
temperature.
2. Press "Set button" to confirm and return to user menu.
Auto / Manual defrosts
1. The appliance will start defrost process automatically for
every 6 hours. When "def" indicator is ON, the appliance is
under defrost process.
2. Under "temperature measuring status", press "Rst button"
for 3s to manually open or close of defrost.
NOTE: Water in the drain tray is evaporated automatically. If
the humidity of environment over 60%, check the drain tray and
throw it away once a day.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
nance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
10
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
• For reasons of hygiene, the appliance should be cleaned be-
• Avoid water contacting the electrical components.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
• No parts are dishwasher safe.
Maintenance
• Check the operation of the appliance regularly to prevent se-
• If you see that the appliance is not working properly or that
or
to adjust the set
• All maintenance, installation and repair work must be car-
Transportation and Storage
• Before storage, always make sure that the appliance has
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
• Do not move the appliance while it is under operation. Dis-
• Special care must be taken when moving or transporting the
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
slightly dampened with a mild soap solution.
fore and after use.
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for cleaning.
Do not use petrol or solvents!
Parts
How to clean
All accessories
• Soak in warm, soapy
such as racks,
water for about 10 to
rack holders, etc.
20 minutes.
• Rinse under running
water thoroughly.
Glass door
• Remove any food
deposits.
• Wipe clean with a soft
cloth and a little mild
detergent. Make sure
no water or moisture
enters inside the of
the appliance.
rious accidents.
there is a problem, stop using it, switch it off and contact the
supplier.
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
been disconnected from the power supply and completely
cooled down.
damage it.
connect the appliance from power supply when moving and
hold it at the bottom.
machine due to its heavy weight. With at least 2 persons or
using a cart. Move the machine slowly, carefully, and never
incline more than 45°.
Remark
Dry all parts
well at last.
Publicidad
