Arktic 233795 Manual Del Usuario página 9

• Do not place any dangerous products, such as fuel, alcohol,
paint, aerosol cans with a flammable propellant, flammable
or explosive substances, etc. inside or near the appliance.
• Once installed, the appliance must not be tilted at an angle
greater than 5° and it is necessary to wait 2h before connect-
ing it to the power supply to switch it on. The same applies if
the appliance is moved afterwards.
• If the appliance has been switched off or disconnected from
the power supply, it is necessary to wait 5 minutes until
switching on again.
• No other appliances should be plugged into the same socket
as with this appliance.
• Do not attempt to climb onto the appliance.
Intended use
• This appliance is intended to be used for commercial appli-
cations, for example in kitchens of restaurants, canteens,
hospitals and in commercial enterprises such as bakeries,
butcheries, etc., but not for continuous mass production of
food.
• The appliance is designed for keep beer, including beverages,
under cool state and to display them for retail sale in restau-
rants, canteens, other commercial enterprises such as bak-
eries, butcheries, supermarkets, etc. Any other use may lead
to damage of the appliance or personal injury.
• Operating the appliance for any other purpose shall be
deemed a misuse of the device. The user shall be solely liable
for improper use of the device.
Grounding installation
This appliance is classified as protection class I and must be
connected to a protective ground. Grounding reduces the risk
of electric shock by providing an escape wire for the electric
current.
This appliance is fitted with a power cord with grounding plug
or electrical connections with grounding wire. The connections
must be properly installed and grounded.
Main parts of the product
(Fig.1 on page 3)
1. Digital control panel
2. Air vents
3. Door key lock
4. Shelf
5. Handle
6. Light
Remark: The content of this manual applies for all listed items
unless specified otherwise. The appearance may vary from the
shown illustrations.
Control panel
(Fig.2 on page 3)
7. Display panel
8. Indicator light status
9. Set button
- Enter the status of parameter setting
- Switch between menu and parameter
10. Rst button
- Exit from parameter setting status
- Exit from one-key recovery status
- Force to start defrost
11. Up
- Adjust menu and parameter
12. Down
- Adjust menu and parameter
- Press 10s to execute parameter one-key recovery
Indicator light status description
Symbol
Status Description
indicator
ON Under setting mode
OFF Operating under the setting condition
ON Compressor works and cooling active
Compressor not works and cooling
OFF
inactive
FLASH Preparing cooling process
ON Under refrigeration process
C
ON Under defrost process
def
ON Under heating process
H
Circuit diagram
(Fig.3 on page 4)
A. DC 12V regulator
B. LED light bar (Max 7W)
C. LED light bar (Max 8W)
D. LED light bar (Max 8W)
E. Fan motor x 2
F. Temperature controller
G. Fan Motor
H. Compressor
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all accesso-
ries. In case of incomplete or damaged delivery, please contact
the supplier immediately. In this case, do not use the device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Operating instructions
1. Place the appliance on a stable and level surface. Ensure
the appliance is properly levelled using a water spirit level
(not supplied).
2. Let the appliance rest in its intended position for about 2
hours before operating to prevent damages to the cooling
circuit through shaken refrigerant.
GB
9